shark S3350 Guide D'utilisation page 4

OPERATING INSTRUCTIONS
Filling your Canister Steam
Cleaner with Water
IMPORTANT:
Always insure that the
unit is "UNPLUGGED" from the wall
receptacle and all switches are in the
"Off" position prior to initial filling or re-
filling the water tank. Never attempt to
fill this unit under a water tap, always
use the filling flask and funnel
provided. Failure to follow these steps
will cause the water tank to overfill and
may pose an electrical safety hazard.
RECOMMENDATION
: The use of
distilled water is recommended,
particularly in areas with hard water in
order to prevent the build-up of lime
scale.
Step 1: Press the safety cap down and
turn counter clockwise until
removed.
Step 2: Assure that the steam cleaner
is empty so that the addition of
the prescribed amount of water
will not result in overfilling.
Step 3: Add 47 fl. oz (1400 ml) of water
using the filling flask and funnel
provided. (Fig. 1) Do not
overfill. Replace safety cap by
turning clockwise - press down
firmly to tighten. Heating time
is approximately 8-10 minutes.
Filling the boiler with hot water
will shorten heat up time.
Step 4: Connect the desired accessory
onto the steam hose.
Step 5: Plug the unit into a standard
120 volt wall receptacle. Press
the On/Off switch. The heating
light will light up.
Step 6: Allow approximately 8-10
minutes for water vapor to
reach its working temperature.
When the unit is ready for use
the steam ready light will light
up.
Step 7: Upon initial use, some water
will come out from the hose
nozzle. This is residual water
that is left over in the hose from
the last use and is normal.
CAUTION: Always point the nozzle
outlet in a safe direction. Never point
in the direction of yourself, other
people or pets.
Fig. 1
NOTE:
When the steam cleaner has
run out of water, steam output will
cease.
Refilling Unit With Water
WARNING: Always allow the unit
to cool for 15 minutes before re-
filling. When re-filling the steam
cleaner while it is still hot, the first
drops of water might bubble up.
Use caution when opening the
safety cap as cap may become hot
during use and escaping steam can
cause scalding.
Step 1: Press the On/Off button on
the unit to the "Off" position.
Step 2: Press the On/Off steam switch
to the "On" position and wait
until no more steam comes
out of the hose.
Step 3: Remove the plug from the
electrical outlet and allow the
unit to cool for approximately
15 minutes before refilling with
water.
Step 4: After completing the cool
down period of step 3 (above),
carefully press down on the
safety cap and turn counter
clockwise to loosen.
5
OPERATING INSTRUCTIONS
Step 5: Slowly pour water using the
filling flask and funnel provided
into the boiler. DO NOT Fill
Under a faucet. Always use
the filling flask and funnel
that are provided. DO NOT
OVERFILL. Never put more
than 47 ounces (1400 ml) of
water in the unit at one time.
Step 6: Screw safety cap back on to
the unit by turning clockwise
and press down to tighten
securely. Plug appliance back
into wall outlet. Steam will start
to be produced as before.
Using Your Steam Cleaner with
Steam Pocket
Step 1: Connect one of the extension
tubes to the hand grip on the
flexible steam hose. To attach
the extension tubes one onto
the other or onto the hand grip,
press the locking button
ensuring that it fits into the hole.
(Fig. 2) To disconnect, repeat
the operation by pressing the
locking button and pulling the
two sections apart.
Fig. 2
NOTE:
Fit the steam pocket frame
with the angle adapter onto the
extension tube.
Step 2: If the angle adapter is not
attached to the steam pocket
frame, attach as follows: Hold
the steam pocket
frame in one hand
and the angle
adapter in the
other. Insert the
angle adapter
Fig. 3
stem into the
opening of the steam pocket
frame as shown in Fig. 3.
Note that the flat on the
nozzle must face toward the
side of the frame with the
brass pin. Once inserted,
rotate it 90°.
Attaching the Steam Pocket
Towel to the Frame
WARNING: Always insure the unit is
"UNPLUGGED" from the wall
receptacle prior to attaching or
removing accessories.
1. Slide the steam pocket towel over
the steam pocket frame. (Fig. 4)
Fig. 4
2. Bring the towel all the way to the
top of the steam pocket frame.
(Fig. 5)
Fig. 5
3. Bring the velcro strips that are on the
back side of the steam pocket towel
over the steam pocket frame and
attach to the inside of the front side of
the steam pocket towel. (Fig. 6)
Fig. 6
6