Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
System cover with sleeve method
HSI150 MA... (HSI90 MA...)
2
ENSystem co ver w ith sleeve m eth od
Table of Contents
1
Publishing Notes ...................................................... 17
2
Explanation of Symbols ........................................... 17
3
Tools and aids required ........................................... 17
4
Description .............................................................. 17
5
Preparing for assembly ............................................ 17
6
Mount system cover ................................................ 17
7
Assembly: Connection for smooth cable ducts ........ 18
8
manufacturers may vary) ......................................... 18
9
MA150 D ................................................................ 18
MA90 D .................................................................. 18
11 Technical data - Dimensions - HSI150 .................... 19
12 Technical data - Dimensions - HSI90 ...................... 19
14 Pipe trench and support .......................................... 20
15 Installation, filling and compression ......................... 20
16 Bending radiuses ..................................................... 20
17 Installation............................................................... 20
17.1 Installation in single rows ..................................... 20
17.2 Installation in multiple rows .................................. 20
18 Assembly ................................................................. 21
and stations............................................................. 21
1 Publishing Notes
Copyright © 2021 by
Hauff-Technik GmbH & Co. KG
Department: Technical Editing
Robert-Bosch-Straße 9
89568 Hermaringen, GERMANY
Tel.
+49 7322 1333-0
Fax
+49 7322 1333-999
E-mail
office@hauff-technik.de
Internet
www.hauff-technik.de
Reproduction of these Installation instructions - even in
extracts - in the form of reprint, photocopy, on electronic
data media or using any other method requires our writ-
ten consent.
All rights reserved.
Subject to technical alterations at any time and without
prior announcement.
These installation instructions form part of the product.
Printed in the Federal Republic of Germany.
Art. No.: 5090030031 Rev.: 01/2021-02-22
2 Explanation of Symbols
1
Work stages
► Effect/result of a work step
1
Reference numerals in drawings
3 Tools and aids required
For the correct installation of the System cover with sleeve
method HSI150 MA... (HSI90 MA...), the following tools
and aids are required in addition to the usual standard
tools:
Tools:
Tool set KES-M-W (Art. No.: 2128030000) consisting of:
- Torque spanner 4 to 20 Nm, 1/4 inch
- Extension 150 mm, 1/4 inch
- Socket for hex driver A/F 13, 1/4 inch
- Socket for hex driver A/F 8, 1/4 inch
4 Description
Description HSI150 MA168 WR (see fig.: 1)
Legend for fig.: 1
1
Cable entry HSI150 K
2
System cover with union nut
3
Transition sleeve KES MA150 - 140
4
Ring clip
5
Corrugated pipe Ø 160 mm
5 Preparing for assembly
1
Remove the protectice foil completely (heat slightly
before).
2
If necessary, clean the spanner inserts in the closing
cover by removing any residual concrete if necessary.
3
Open the closing cover using the articulated face
spanner SLS 6G (accessory) or, if the perimeter insula-
tion SLS 6G(D) (accessory) has been applied, using the
spanner inserts by means of movement to the left
(see fig.: 1).
6 Mount system cover
1
Insert the pre-assembled system cover into the bayo-
net of the wall insert by means of a light rotational
movement and ensure it is turned to the right as far
as it will go (the red clamping nut may not yet be
tightened) (see fig .: 3).
► When correctly mounted, the arrows on the system
cover match up with the arrows on the square frame
of the wall insert (see fig .: 4 and 5).
2
Tighten the clamping nut by turning it to the right by
hand or using the articulated face spanner SLS 6G(D)
EN
17
Publicité
Chapitres
Table des Matières
