System Requirements; English - i-tec U3DUALHDMIDOCK Mode D'emploi

DESCRIPTION
1. 2x USB 3.0 type A ports – for connecting USB devices to the docking station; USB 3.0
Fast port also provides features in line with the BC 1.2 specification
2. 1x audio jack for headphones / speakers
3. 1x audio jack for microphone
4. 4x USB 2.0 type A ports – for connecting USB devices to the docking station
5. 1x Ethernet 10 / 100 / 1000 Mb/s GLAN RJ-45 port – for connecting to an Ethernet
network or internet modem
6. 2x HDMI port – for connecting monitors
7. 1x USB 3.0 type B port – for connecting the docking station to the USB port of a laptop
/ tablet / PC
8. 1x power supply connector – for connecting a power adapter

SYSTEM REQUIREMENTS

• Hardware requirements: notebook / tablet / PC with a free port USB 3.0 / 2.0. If you
have USB 2.0, the data transfer speed will be reduced. Processor Intel Pentium 1.2
GHz and higher, 512 MB RAM.
• Operating system: Windows XP SP3 / Vista / 7 / 8 / 8.1 / 10, macOS X, Linux Ubuntu
14.04, 16.04, 17.04, 17.10, 18.04, 19.04, Android 5 or later, Chrome OS R51 or later
• For playing a DVD on an additional monitor the processor shall be at least Intel
Pentium 2.0 and higher, 1 GB RAM and a screen resolution shall be 800x600 and
16 colors.
CAUTION!
Charging: The docking station supports charging of the connected USB mobile
equipment such as smartphones, ebook readers, multimedia players, GPS navigations
and tablets (e.g. Asus, Toshiba, Dell, GoClever, Prestigio, Emgeton, Sencor). Simply
connect the equipment you want to charge using the original cable to the USB port of the
docking station with the connected power adaptor. The only exceptions are the Apple or
Samsung tablets which are supported as well but only on the USB 3.0 Fast port with the
BC 1.2 specification. At the same time the docking station must be disconnected from
the computer/notebook and the inclosed power adaptor must be connected.
USB 3.0: Before the installation on the USB 3.0 port make sure that you have the most
recent drivers installed for this port (for the USB 3.0 controller into notebook / tablet /
PC). Products with the USB 3.0 SuperSpeed technology have been used since 2010;
however, the drivers for the supported equipment are still undergoing some fine tuning.
Your notebook / tablet / PC needs to be equipped with the USB 3.0 interface so that you
can utilize the advantages of the fast USB 3.0 equipment. Its problem free function is
ensured by the chipset which needs to have the current drivers available.
Problems that you can encounter during the installation or use of our USB 3.0 equipment
are very often caused by the installed outdated drivers for the USB 3.0 controller or
chipset of your notebook / tablet / PC. Other problems can be caused by outdated
firmware of the USB 3.0 port controller. Most frequently it is one of the following
manufacturers: Intel, Renesas (former NEC), Via (VLI), AS Media, Fresco Logic, Etron.
You can find the most recent drivers for the i-tec products on our website www.i-tec.cz/en
in the „Download" tab for the individual products.
INSTALLING DRIVERS ON WINDOWS 7 / 8 / 8.1 / 10 (32/64 BIT VERSION)
ATTENTION! Do not connect the docking station to your laptop / tablet until you install
the corresponding drivers. Drivers only need to be installed before first use. Before
installation, make sure your system uses the latest drivers for your device and its BIOS
is up-to-date.
To download drivers for Windows 7/8/8.1, visit our website at www.i-tec.cz/en and go to
Quick Start
| 5

ENGLISH