Technical Data; Attachment And Operation - Scheppach TPH500 Traduction Des Instructions D'origine

Children must always be supervised in order to
ensure that they do not play with the equipment.
Do not lose this safety information.
Residual risks
The machine has been built using modern technology
and in accordance with recognized safety rules.
Some hazards, however, may still remain.
• Risk of injury to fingers and hands from the tool in
operation during improper use.
• Electrical hazards when unsuitable electric con­
nections are used.
• Safety hazard from the hedge clippers in case of
long hair and loose clothing; Wear personal protec­
tive equipment such as a hair net and tight work
clothing.
• Although having regarded all considerable rules
there may still remain not obvious remaining haz­
ards.
• Minimize remaining hazards by following the in­
structions in "Safety Rules", "Use only as author­
ized" and in the entire operating manual.

6. Technical data

Cutting data hedge trimmer
Cutting circle diameter mm
Bar length mm
Cutting length mm
Max. cutting speed max.
min
­1
Telescope length min./
max. mm
Tilting range
Power unit
Engine V / Hz
Engine output W
Weight kg
Subject to technical changes!
Information concerning noise emission measured ac­
cording to relevant standards:
Sound pressure L = 84 dB(A)
pA
Sound power L = 91 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration left hand A = 4,8 m/s
hv
Vibration right hand A = 3,5 m/s
hv
Uncertainty K = 1.5 m/s
2
PA
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
18
450
410
1540
1900­2500
0° ­ 120°
230 - 240 / 50
500
3.5
2
2
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked
the places that have to do with your safety with
this sign: m

7. Attachment and operation

ATTENTION! Before working on the device ­ clean­
ing, inspection, maintenance or other work - always
turn off the device and separate it from the power
supply.
ASSEMBLY
Assembling the motor casing (Fig. 2)
• Open the quick acting lock (11) from the motor cas­
ing (9).
• Insert the telescopic tube (6) into the casing's hold­
ing fixture.
• Close the casing's quick acting lock (11) again,
Attaching the shoulder strap (Fig. 3)
Assembly and use:
• Fix the shoulder strap on the flap (4)
• By changing the adjuster, the length of the shoul­
der strap can be altered. Adjust the length of the
shoulder strap in such a way that it ensures a com­
fortable working posture.
• Put the shoulder strap over your right shoulder.
• Carry the tool's motor on the right side of your
body.
Never put the shoulder strap over your shoulder
and across your chest, but put it on one shoul-
der. In this way, you will be able to quickly re-
move the tool from your body in case of emer-
gency.
m Warning! Use only original manufacturer's re­
placement parts, accessories and attachments. Fail­
ure to do so can cause poor performance, possible
injury and may void your warranty. Never use the
machine without the guard assembled!
Starting and stopping the telescopic hedge trim-
mer (Fig. 4)
• Starting the device: First, press the safety switch
(3) on the back handle left, then the trigger (2). Af­
ter starting the motor, you can release the safety
switch (3).
GB | 23