Setting The Screen Saver - Clarion DXZ948RMP Mode D'emploi

Operations Common to Each Mode
Main Item
SOUND AC-PRO III
• Selecting the VSE mode (STD/PRO) (cf. page 44)
EQ SELECT
• Selecting the equalizer mode (cf. page 44)
SP-SETTING
• Setting the speaker configuration (cf. page 44)
CENTER-SP / SUB-WOOFER
• Setting sub-woofer speaker ON/OFF (cf. page 45)
HPF / SUB-W LPF
• Adjusting the speaker filter frequency (cf. page 45)
AMP CANCEL
• Setting internal amplifier use ON/OFF (cf. page 46)
SP GAIN
• Adjusting the speaker output level (cf. page 46)
PL II DELAY SRD-SP
• Adjusting the rear speaker delay time (cf. page 46)
PL II CONT PANORAMA / DIMENSION / CTR WIDTH
• Setting the music mode in detail (cf. page 47)
TUNER TV ARER
• Setting the TV area (cf. page 57)
TV DIVER
• Setting TV diversity (cf. page 57)
LINK ACT
• Setting the AF function between RDS and DAB (cf. page 26)
LANGUAGE
• Setting the PTY screen language (cf. page 30)
RDS-INT 2Z
• Setting the RDS interrupt while the 2-ZONE function is in use
(cf. page 30)
SETTING AUX / TEL
• Setting AUX and TEL (cf. page 47)
AUX SENS
• Setting the portable audio (AUX) input level (cf. page 48)
TEL-SP
• Setting the car speaker output for the cellular phone
(Optional TEL-002) (cf. page 48)
TEL-SWITCH
• Cellular phone interrupt setting (cf. page 48)
CALIBRATE / A-VOL SENS
• Setting the auto-volume function (cf. page 49)
SYSTEM CHECK
• Performing a system check (cf. page 49)
CODEMATIC
• Setting security (cf. page 50)
40
DXZ948RMP
Sub-item

Setting the screen saver

(SCREEN SVR)
This function allows you display a screen saver
when you have not operated this unit for about
30 seconds.
• The factory default setting is "ON".
1. Press the [A] button to set to the adjust
mode.
2. Touch on the setting item display to
select "SCREEN SVR" under "DISPLAY".
ADJUST MODE
SCREEN SVR ON
DISPLAY
3. Either touch on the right of the
display, or turn the [ROTARY] knob to select
"ON" or "OFF".
4. Press the [A] button to return to the original
mode.
To switch the screen saver display
Touch PREV or NEXT while the screen saver is
displayed.
Each touch of these buttons switches the
screen saver display.
Screen savers
Screen saver pattern 1
Screen saver pattern 2
Screen saver pattern 3
Spectrum analyzer pattern 1
Operations Common to Each Mode
Spectrum analyzer pattern 2
Spectrum analyzer pattern 3
Spectrum analyzer pattern 4
Message information
MESSAGE
PREV
A c t i v e M a t r i X C o n t r o l S y s t e m
A c t i v e M a t r i X C o n t r o l S y s t e m
NEXT
SS SCAN
The above 8 indications are displayed for
about 10 seconds each.
Entering messages to display
in message information
(MSG INPUT)
1 type of screen saver is available. For details
on how to switch the screen saver display, see
"Setting the screen saver".
• Up to 30 characters can be entered.
• The factory default setting is "Active MatriX
Control System".
1. Press the [A] button to set to the adjust
mode.
2. Touch on the setting item display to
select "MSG INPUT" under "DISPLAY".
ADJUST MODE
MSG INPUT ED I T
DISPLAY
3. Touch EDIT.
The mode changes to the message entry
mode.
DXZ948RMP
41