Clarion DXZ948RMP Mode D'emploi page 13

Radio Operations
Tuning
There are 3 types of tuning mode available,
seek tuning, manual tuning and preset tuning.
Seek tuning
There are 2 types of seek tuning: DX SEEK and
LOCAL SEEK.
DX SEEK can automatically tune in to
receivable broadcast stations, while LOCAL
SEEK can tune in to only broadcast stations
with good reception sensitivity.
1. Touch BAND to select the desired band (FM
or AM (MW, LW)).
2. Tune into a station.
∗ When MANU is displayed, touch and hold
BAND for 1 second or longer.
"MANU" in the display goes off and seek
tuning is now available.
∗ If "TA" is lit in the display, TP stations are
automatically sought.
DX SEEK
When is touched in the frequency display,
automatic tuning starts.
When is touched, the station is sought in
the direction of higher frequencies; when
touched, the station is sought in the direction of
lower frequencies.
∗ When seek tuning starts, "DX SEEK" appears
in the display.
LOCAL SEEK
When is touched in the frequency display,
local seek tuning is carried out. Broadcast
stations with good reception sensitivity are
selected.
∗ When local seek starts, "LO SEEK" appears
in the display.
24
DXZ948RMP
Manual tuning
There are 2 ways available: quick tuning and
step tuning.
In the step tuning mode, the frequency changes
1 step at a time. In the quick tuning mode, you
can quickly tune the desired frequency.
1. Touch and hold BAND for 1 second or longer
while MANU is not displayed.
Manual tuning is possible when MANU is
displayed.
2. Operate the frequency display to tune to a
frequency on which there is a broadcast.
Step tuning
Touch on the frequency display.
Quick tuning
Touch on the frequency display. Tuning
stops when you take your finger away from the
panel.
Recalling a preset station
Recalling a preset station is a function for tuning
pre-stored stations.
1. Touch and hold MODE for 1 second or
longer.
is
The preset memory list is displayed.
2. Touch the station you want to listen to.
∗ In the normal mode, preset No. can also
be tuned by touching in the main
display.
To cancel tuning
1. Touch RTN.
Preset memory
A total of 24 preset positions (6-FM1, 6-FM2, 6-
FM3, 6-AM) exists to store individual radio
stations in memory.
1. Touch BAND to switch the reception band.
2. Operate the frequency display to store the
station to.
3. Touch and hold MODE for 1 second or
longer.
The preset memory list is displayed.
4. Touch and hold the preset No. to store the
station to for 2 seconds or longer.
You will hear a long beep, and the station is
stored in memory.
Auto store
Auto store is a function for storing up to 6
stations that are automatically tuned in
sequentially.
1. Touch MODE.
2. Touch and hold A-STORE for 2 seconds or
longer.
The MODE display changes to "A-STORE"
and the preset No. in the auto-store
operation appears on the preset No. display.
∗ Stations with good reception are
automatically searched, and are stored to
preset memory (No.1 to No.6) in order
from the station having the lowest
frequency.
Notes:
• When auto store is performed, stations stored to
memory so far are cleared.
• When there are fewer than 6 stations with good
reception in LOCAL SEEK, low frequencies are
automatically returned to, and auto store is
performed again by DX SEEK. If there are fewer
than 6 stations even after auto store is performed
twice, stations stored so far remain in memory.
• If auto store is performed in the FM bands, the
stations are stored in FM3 even if FM1 or FM2
was chosen for storing stations.
Radio Operations
Preset scan
Preset scan is a function for receiving stations in
the order that they are currently stored to preset
No. so that broadcasts can be checked.
1. Touch MODE.
2. Touch P-SCAN.
The MODE display changes to "P-SCAN"
and the preset No. in the preset scan
operation is displayed in the preset No.
display.
* The currently stored stations are received
in order for 7 seconds or longer each.
Stations with poor reception are skipped,
and the next station is received.
When preset scan is performed in an FM
broadcast, FM stations are received as
follows:
FM1 (1 6) FM2 (1 6) FM3 (1
6)...
When preset scan is performed in an AM
broadcast, AM stations are received as
follows:
AM (1 6) AM (1 6) and so forth.
To cancel preset scan
1. Touch P-SCAN.
The P-SCAN display changes to "MODE",
and the stations that were being received
when P-SCAN was touched are received
next.
DXZ948RMP
25