Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
i
I
(
)
6, detail 2
Drill holes at the previously marked points where
the attachment brackets are for the shower tray and insert the plugs in
the holes that you have made.
i
I
(
)
6, detail 3
Drill holes at the previously marked points (wall
frame wall attachment) and insert the plugs.
i
I
(
6, detail 4
)
Replace the compensators by lining them up with
the drilled holes then, checking that they are straight, fasten them
with the screws and washers as shown.
Wall panel installation
i
I
(
7-8, detail 1-2
)
Pull the shower tray out from the wall and
place the panel on the shower tray edge so that the latter's holes
match up with the holes in the panel's frame.
Since this operation must be carried out by standing on the
shower tray, it is advisable to cover it with suitable protection.
i
I
(
7-8, detail 2
)
Fasten the unit with 5 (3+2) screws, 5 (3+2) ser-
rated washers and 5 (3+2) "grower" washers.
i
(
)
9
For ELT3, 4 and 22 models, check that the over-
flow hose (A), from the tank stays positioned inside the
shower tray.
Connect the B hose (coming from the drainage column) to the boil-
er/tank drain using a plastic clamp (to be found in the bolt and screw
pack) by passing it through the hole in the shower tray. Also check
that the clamp on the side attachment of the drainage column is firm-
ly tightened.
Glass panel installation
i
I
(
)
1-1a; 2-2a
Remove the fixed glass panel from its packag-
ing (A) - (Thema 100) or (A) (A1) - (Thema 120) and also the s-
liding glass panel (B), the handles (D), the compensators (E), the a-
luminium inspection panels (F) and (F1) (or the ones with mirrors,
if provided) the click-on covers (G) and (G1) and the seals (N).
i
I
(
)
10, detail 1
Fasten the nylon washers and the pins to the
sliding glass panel according to the shown sequence.
Tighten both pins to fasten the handle (the one without holes for the
grub screw) onto the outside of the glass panel.
i
I
(
)
10, detail 2
Fasten on the inside handle and, using the Allen
spanner provided, tighten the side grub screws.
Repeat these operations for the other handle.
For the THEMA100 model only
i
I
(
11, detail 1
)
Position the fixed glass panel (A) on the show-
er tray checking that:
1a) the lower runner groove fits into the raised edge of the show-
er tray;
1b) the fixed glass panel upright is placed inside the wall panel
profile;
i
I
(
11, detail 2) Then fasten the glass panel unit to the wall pan-
el profiles using the 10 screws + 10 washers provided.
For the THEMA120 model only
i
I
(
12, detail 1
)
Position the fixed glass panel (A1) on the show-
er tray checking that:
1a) the lower runner groove fits into the raised edge of the show-
er tray;
1b) the fixed glass panel upright is placed inside the wall panel profile;
i
I
(
12, detail 2) Then fasten the glass panel unit to the wall pan-
el profiles using the 5 screws + 5 washers provided.
i
I
(
)
13, detail 1
Position the fixed glass panel (A) on the show-
er tray checking that:
1a) The bottom sliding profile fits into the bottom angle bar (C);
1b) The bottom slide's groove fits into the shower tray's raised edge;
1c) The fixed glass panel upright is placed inside the wall panel profile;
1d) The top sliding profile fits into the top angle bar (C1);
i
I
(
13, detail 2) Then fasten the bottom left sliding profile to the
angle bar (C).
i
I
(
13, detail 3) Fasten the top left sliding profile to the angle
bar (C1).
i
I
(
13, detail 4) Then fasten the glass panel unit to the wall pan-
el profiles with the 5 screws +5 washers provided.
THEMA100-120 model
i
I
(
14, detail 1) Fasten the two seals (N) to the sliding glass
panel (B).
i
I
(
14, detail 2) Fasten the sliding glass panel, hooking the up-
per rollers onto the corresponding sliding profiles.
i
I
(
14, detail 3) Adjust the screws for the supports, lift the glass
panel until the sliding blocks fit into the lower runners.
During this operation also check that the glass panels are perfect-
ly vertical and slide easily.
i
I
(
15-16) Fasten the glass panel unit to the shower tray using 3
(THEMA 100) - 4 (THEMA 120) metal brackets (in the hardware fittings
pack) and insert them first into the groove of the lower runner and then
fasten them to the shower tray using the screws and washers provided.
Top installation (if provided)
i
I
(
)
17, detail 1
Place the top over the shower enclosure, so that
the edge fits into the runner groove of the top slide; instead the back
edge of the top must rest on the metal frame of the wall panel and be
fastened to the top using 2 screws and 2 washers.
i
I
(
)
17, detail 2
Then connect the shower head's fabric-finish
rubber hose to the respective solenoid valve on the left side of the
shower enclosure using a metal clamp; be careful not to tighten it
too hard or you may cut the hose.
12
Publicité
Table des Matières
