General Information On Safety Regulations; Warranty Terms And Conditions; Tables - Project 2000 12600 Série Manuel D'utilisation

Bed lifting system components overhaul or replacement shall be carried out within a reasonable time of 36 months
A "control register" has been defined to this purpose (Annex I par. 4.4.2 line b) enabling the user to carry out periodical checks of the bed
lifting system completeness in order to preserve safety conditions (ANNEX 1)
THE MANUFACTURER SHALL BE HELD HARMLESS IN CASE ANY COMPONENTS OR DISASSEMBLED PARTS OF THE BED LIF-
TING SYSTEM ARE RECYCLED FOR USE.
DISPOSAL OF ELECTRIC AND ELECTRONIC COMPONENTS:
Electric and electronic devices classified as waste pursuant to art. 6, par. 1, letter a) of the Legislative Decree of February 5th 1997, No.
22 and following modifications are defined as "Waste electrical and electronic equipment" or "WEEE", including all components, sub-
groups and consumables that are integral part of the product; an improper use of the equipment or part of the equipment can cause
serious damage to environment and health due to the presence of hazardous materials contained.
Pursuant to Legislative Decree 151/2005 it is therefore forbidden to dispose of WEEE as urban waste and it is necessary to collect WEEE
separately. Fines shall otherwise be applied for illegal waste disposal pursuant to Legislative Decree of February 5th, 1997, No. 22.
WEEE collection systems and "WEEE collection centers" have been defined by the public administration as areas, buildings and structu-
res for separate collection and temporary stocking of WEEE, opened to citizens.
It is furthermore possible to return the system to the retailer when purchasing a new one.
The logo for separate collection of electrical and electronic equipment (EEE) is a crossed-out wheeled rub-
bish bin: this logo is printed directly on the product in a visible position and it is well readable and indelible.

11.0 GENERAL INFORMATION ON SAFETY REGULATIONS

All dangerous equipment such as shafts, pulleys, chains, crown gears, etc. has been isolated and protected - within structural limita-
tions - with suitable protection panels.
The aforementioned panels, which effectively protect the user against dangerous components, shall not be removed, not
even temporarily, and they shall be protected against interference throughout the bed lifting system life.
If it is necessary to remove the protections, the operator shall however follow safety instructions in order to protect him/herself and
any other person in the operation area of the bed lifting system. Protections shall however be put back into place as soon as the main-
tenance operation is finished.
More specifically, it is necessary - while performing maintenance operations - to:
• Make sure the vehicle is parked and secured in safe and stable conditions before starting maintenance operations.
• Carry out each operation with the vehicle parked and only after disconnecting power.
• THE BED LIFTING SYSTEM MUST NEVER BE USED WHILE THE VEHICLE IS RUNNING

12.0 WARRANTY TERMS AND CONDITIONS

The Manufacturer "Project 2000" guarantees the bed lifting system components for 24 months after purchase. Defective parts shall not
be tampered with and they shall be returned together with the serial number indicated on the plate located on the bed lifting system.
Parts that have been tampered with or partially disassembled will not be covered under warranty. Electronic control units will not
be covered under warranty in case of incorrect connection detection to the system: in this case repair costs will be charged to the
customer.
The Manufacturer "Project 2000" may decide to replace defective components instead of repairing them. Should replacement or repair
have a negative outcome, the customer can charge repair costs to the Manufacturer or cancel the purchase.
WARRANTY WONT BE APPLIED IF THE NECESSARY PERIODIC CHECK UPS, REQUESTED IN THIS HANDBOOK,
ARE NOT CARRIED OUT AND NOTED.
The manufacturer will not be liable for any indirect damage.
DAMAGES CAUSED BY IMPROPER USE OF THE BED LIFTING SYSTEM, OR USE NOT IN COMPLIANCE WITH THE INSTRUCTIONS
PROVIDED IN THIS MANUAL, WILL NOT BE COVERED UNDER WARRANTY.
36
The warranty covers repair or replacement of parts at the Manufacturer's (Project 2000) premises. Transport costs (for spare
parts under warranty) as well as retailer labour costs or other costs required by the user are not covered under warranty.
All disputes shall be subject to the jurisdiction of the court of Florence (Italy).

13.0 TABLES

37