ADB MEMORACK 15 Manuel D'utilisation page 8

MEMORACK 15
MEMORACK 30
How to test all the dimmers (Test Chaser)
The Test Chaser runs continuously through all the dimmers.
depress + or - until Test Chaser ?
the display shows Chaser ... : ...%
depress <— to end the chaser, to restore normal operation, and to
return to the main Menu.
Available dimmer laws
Your MEMORACK stores 10 dimmer laws :
linear rms voltage
linear to 120 V
fluorescent lighting
linear5% preheat
square law
non-dim (on at 15%)
spares/specials
Mix indicates that some dimmers are set to a different law.
How to set the same dimmer law for all dimmers
Example : to set all dimmers to the Linear dimmer law
select Menu 2, as indicated above
depress + or - until Dimmer Law ?
the display shows Dim. All: ...
depress + or - until Dim. All: Lin
How to modify the dimmer law for one dimmer
Example : you wish to set dimmer No. 2 to On/Off.
select Menu 2, as indicated above
depress + or - until Dimmer Law ?
the display shows Dim. All: ...
depress + until Dim2 : ...
depress + or - until Dim2 : OnOf
depress <— to return to the main Menu
How to Record a cue (record)
Example : you wish to record into memory N°2.
First set the correct levels with the lighting console. Then your
MEMORACK can make a snapshot:
select Menu 2, as indicated above
depress + or - until Memories ?
depress + until Record Mem.
depress + or - until Rec. Mem. 2
the display shows Mem. recorded to confirm
The # symbol precedes the number of a cue which already exists.
How to play back a memorized cue (Play)
Your MEMORACK can store 20 lighting cues (memories), dimmer
levels, Fade and Wait times. To play back cue #2 :
select Menu 2, as indicated above
depress + or - until Memories ?
the display shows Play Mem. ?
depress + or - until Play Mem # 2
the display shows Playing Mem # 2
depress + or - and then YES to play back another cue
depress <— to stop play-back and
depress <— to return to the main Menu
How will DMX coexist with the Memories?
depress + or - until Memories ?
depress + until Prior. Mem/DMX?
OR you wish that the DMX and Analogue inputs will be discarded during
Play Memory
depress + until Masked
depress <— to return to main Menu
8
depress
with dimmer N°
and level
Lin
120V
Fluo
Preh
Sqr.
TV TV
OnOf
Sp....
depress
depress
depress
depress
depress
depress
depress
depress
depress
depress
depress
depress
depress
depress
depress
depress
OR you wish that the highest level among DMX, Memory and Analogue
takes precedence
depress + until
YES
depress <— to return to main Menu
Cue N° 0: the Priority Cue
Memory (cue) N°0 is the Priority Cue. Its playback will always temporarily
disable the DMX and Analogue inputs. This is not influenced by the
setting in Prior. Mem/DMX?
Application: play-back of a predefined emergency cue with limited total
current consumption. Priority Cue N°0 is not included in the Memory
Chaser.
Automatic play-back of a cue at power-up
If the mains supply was switched off while your MEMORACK was in the
Memo Playing or Memory chaser mode, then it will automatically
resume that mode when power is switched on again.
depress <— to stop play-back, and
depress <— to return to the main Menu
How to Edit a cue (Edit)
You can create or modify a lighting cue in your MEMORACK, by means
of the Edit function.
Example: memory 10, set dimmer N° 2 at 80%
YES
select Menu 2, as indicated above
YES
depress + or - until
YES
depress + until
depress + or - until
depress + or - until
depress + or - until
After setting the last dimmer level, you can set the Fade time (min.s) for
YES
that cue, followed by the Wait time for the Memory Chaser.
+
An infinite wait time is available to create a memory chaser which does
YES
not loop back.
YES
To select an other memory to edit:
depress <—, then + or - and then YES
To end Edit depress <—
and <— to return to the main Menu
How to run the memory sequence (Memory Chaser)
Memory Chaser runs an automatic timed sequence of cues #1 to #19.
depress + or - until
YES
depress + until
YES
depress + to select the starting memory
YES
depress YES
The display shows the sequence of events: Fading -> #... during a
fade, followed by Playing #...
How to display the DMX levels
select Menu Level 2, as indicated above
depress + or - until
depress + or - to review the DMX levels of the dimmers
YES
depress <— to return to the main Menu.
YES
Example : if the display shows DMX 1:69% then dimmer No. 1
YES
receives a control level of 69% from the DMX512
inputs.
How to display the Analogue levels
select Menu 2, as indicated above
depress + or - until
YES Similar to View DMX, but displays the Analogue Input levels (if applicable).
YES A temporary message will inform you of the setting of the analogue
inputs:
Muted/Absent; Enabled 0/+10V; Special 1; Special 3; Special 4.
YES
Dim 6 : DMX 512
DMX&Mem.: HTP depress
Memories ? depress
Edit Mem ? depress
Edit Mem 10 depress
Dim 2: ...% depress
Dim 2: 80% depress
Memories ? depress YES
Mem Chaser ? depress YES
to start the Memory Chaser
View DMX ? depress
View Analog ? depress
Lighting Technologies
YES
YES
YES
YES (x2)
YES
YES
YES
YES