Quick DP3 PRINCE Série Manuel De L'utilisateur page 17

N. DESCRIPTION
1 Bent anchor winch lever
2 O-ring
3 Drum bush DP3 chromed
4 Drum 1000W
5 Gypsy cover
6 Top clutch cone
7A Gypsy 8 mm
7B Gypsy 10 mm
8 Bottom clutch cone
9 Screw M 6*55 stainless steel
10 Spring washer
11 Oil seal
12 Internal circlip
13 External circlip
14 Bearing
15 Short shaft
16 Oil seal
17 Key
18 Long shaft
19 Chain guide cover stainless steel
20 Screw 3,9*25 stainless steel
21 Screw M5*50 stainless steel
WARNING: make sure the electrical power to the motor is switched off when working manually on the windlass.
Carefully remove the chain or rope from the gypsy or the rope from the drum.
Quick windlasses are manufactured with materials resistant to marine environments. In any case, any salt deposits on the
®
outside must be removed periodically to avoid corrosion and damage to the equipment. The parts where salt may have built up
should be washed thoroughly with fresh water.
Once a year, the drum and the gypsy are to be taken apart as follows:
DRUM VERSION
Use the handle (1) to loosen the bush (3); pull off the drum (4) and the top clutch cone (6); loosen the fixing screws (9) of the
rope/chain stripper and remove it. Pull off the gypsy (7).
NO-DRUM VERSION
Use the handle (1) to remove the gypsy cover (5); remove the top clutch cone (6); loosen the fixing screws (9) of the rope/
chain stripper and remove it and pull off the gypsy (7).
Clean all the parts removed to avoid corrosion, and grease the shaft thread (15 or 18) and the gypsy (7) where the clutch cones
(6 and 8) rest (use grease suitable for marine environment).
Remove any oxide deposits from the terminals of the electric motor and the contactor unit; grease them.
DP3 700/1000/1500W - REV003A
www.busse-yachtshop.de | info@busse-yachtshop.de
22 Mooring rope puller DP3
23 Spring for pressure lever
24 Pressure lever
25 Cylindrical stainless steel pin 5*40
26 Screw M4*26 stainless steel
27 Screw M5*40 stainless steel
28 Screw M4*25 stainless steel
29 Screw M4*40 stainless steel
30 Plastic chain pipe series DP3
31 Screw M8*20 stainless steel
32 Cover Base DP3 stainless steel
33 Plastic cover insert DP3
34 Aluminium round base DP3
35 Nut M 4 stainless steel
36 Nut M 5 stainless steel
37 Nut M 6 stainless steel
38 Gasket/ DP3 - shaped jig
39 Sensor
40 Stud 8*080 Ø8 stainless steel
41 Gearbox flange gasket TOP TG50
42 Gearbox flange gasket TOP TG60
43 Gearbox - Quick TG50 1000W
44 Washer
MAINTENANCE
45 Grower
46 Nut
47 Washer
48 Self locking nut
49 O-ring
50 Gearbox - Quick TG70 1500W
51 Key 5x5x15
52A Electric motor 700W 12V
52B Electric motor 700W 24V
52C Electric motor 1000W 12V
52D Electric motor 1000W 24V
52E Electric motor 1500W 12V
52F Electric motor 1500W 24V
53A Motor protection case 700W
Motor protection case
53B
1000/1400W
54 Grommet
55 Terminal board cover
56 Screw
57 Bottom gasket
58 Bottom protec cover
59 Cable outlet
GB
17