Technical Data; Attachment And Operation - Scheppach LBH2600P Traduction Des Instructions D'origine

6. Technical data

LBH2600P
Technical data
Dimension LxWxH mm
Air speed max. km/h
air volume min./max. m 3 /min
dust bag capacity l
Power unit
Displacement cm3
Max. engine output kW
Idle speed min-1
Fuel tank capicity cm3
Engine type
Blower weight kg
Vacuum weight kg
Total weight kg
Subject to technical changes!
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure L = 97,0 dB(A)
pA
Sound power L = 108,4 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration
Lower handle A = 15,1 m/s
hv
Upper handle A = 11,92 m/s
hv
2
Uncertainty K = 1.5 m/s
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked
the places that have to do with your safety with
this sign: m

7. Attachment and operation

ATTENTION! Before working on the device - clean-
ing, inspection, maintenance or other work - always
turn off the device.
ATTENTION!
Remove transport protection ring (23) Fig 1
Assembly blower(Fig 7-9)
m Warning: The blower must not be used or
switched on until it has been fully assembled.
1050x250x350
260
-
50
25,4
0,7
3500 ± 300
650
2-stroke
engine, air-
cooled
4,7
5,6
6,4
2
2
• Remove the screw (K) and its washers (L).
• Align the first blower tube(4) compartment with
the protrusion of the air outlet, push the tube and
turn it 90° clockwise, in order to permanently fix
it in place.
• Fix the tube (4) to the air outlet using the screw (K)
and its washers (L).
• Align the second blower tube(5) compartment with
the protrusion (P) of the first tube, push the tube
and turn it 90° clockwise, in order to permanently
fix it in place.
m Warning! Use only original manufacturer's re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty. Never use the
machine without the guard assembled!
Assembly vacuum collector (Fig 10 - 14 )
• Warning: The vacuum collector must not be
used or switched on until it has been fully as-
sembled.
• Remove the screw (1) and the washer (2).
• Align the tube (18) with the projection of the Air
outlet, then slide the Pipe over the air outlet and
turn it over 90 ° counterclockwise to make it per-
manent to fix.
• Insert the pipe end (18) into the catch bag (17) and
close the opening with the supplied Velcro tape.
• The pipe (18) with the screw (K) and the washers
Secure (L) to the air outlet.
• Release the star grip (21) and remove the protec-
tive grille (22) to open.
• Align the suction pipe (19) with the projection from
the inlet, slide the pipe in the direction of the pro-
jection and turn it 90 ° clockwise to fix it perma-
nently.
• Align the second suction pipe (20) with the Slide
out the projection of the first tube (19)You put the
two tubes together and turn them Turn it 90 °
clockwise to make it permanent fix.
• The engine can not start if you do not assemble
the vacuum tube when using as a vacuum.
Operation
Before starting
Each time before use, check the following:
• That there are no leaks in the fuel system.
• That the equipment is in perfect condition and that
the safety devices and cutting devices are complete.
• That all screws are securely fastened.
• That all moving parts move smoothly.
• That the protective flap (E) is closed and that all
security switches (F) are activated (fig. 15).
GB 23