Technical Data - EINHELL ROYAL RT 551 Mode D'emploi

Anleitung RT 551 SPK 7
GB
the ground. For example, do not try to cut grass
growing on walls, rocks, etc.
Within the working radius of the grass trimmer
the user is responsible for any damage caused
to third persons by use of the trimmer.
Never cross roads or pebble paths with the grass
trimmer switched on.
When you are not using the grass trimmer, keep
it in a dry place out of the reach of children.
Use the grass trimmer only as described in these
directions for use and always hold it vertical to
the ground. All other positions are dangerous.
Check the screws regularly to see that they are
properly tightened.
The mains voltage must be the same as the
voltage specified on the rating plate.
Check the power cable regularly for signs of
damage or aging. Never use the grass trimmer if
the power cable is in less than perfect condition.
Power cables used with the trimmer must not be
of a lighter duty class than HO7RN-F rubber-
insulated flexible cables according to DIN 57282
/ VDE 0282 with a minimum diameter of 1.5 mm
Plug connectors must be equipped with earthing
contacts and the coupling must be rain-water-
protected.
Keep cables and other objects out of the area
you want to cut.
If you have to lift the grass trimmer to move it,
switch off the motor and wait for the rotating tool
to stop. Before you leave the trimmer, switch off
the motor and pull out the power plug.
Before you connect the grass trimmer to the
power supply, make sure that none of its moving
parts are damaged and that the line spool is
correctly inserted and fastened.
Never cut against hard objects when using the
grass trimmer. This is imperative to avoid
causing injury to the user and damage to the
trimmer.
Use only original replacement parts for repair
and maintenance purposes.
Have repairs carried out only by a qualified
electrician.
Examine the grass trimmer for signs of wear or
damage each time before you use it and after
any collisions. Have essential repairs carried out
without delay.
Always keep your hands and feet away from the
cutting mechanism, particularly when you switch
on the trimmer.
After pulling out new line, always return the
trimmer to normal working position before you
switch it on again.
Never use replacement parts or accessories
which are not foreseen or recommended by the
12
22.10.2003 8:00 Uhr Seite 12
manufacturer.
Pull out the power plug before carrying out any
inspection, cleaning or other work on the trimmer
and whenever it is not being used.
Caution! The nylon line will run on for a few
seconds after the tool is switched off!
3. Symbols used on the appliance (see
Figure 2)
Item 1: Warning
Item 2: Wear eye protection
Item 3: Protect from moisture
Item 4: Read the instruction manual before starting
2 .
Item 5: Pull out the mains plug before checking a
damaged power cable
Item 6: Keep other people out of the danger area
Item 7: The tool continues to rotate

4. Technical data

Voltage
Power rating
Cutting width
Speed
Nylon cutting line
Sound pressure level LPA
Sound power level
Vibration aw
Weight
The noise level of this machine may exceed 85
dB(A). In this case, noise protection measures need
to be introduced for the user. The machine's noise
was measured in accordance with IEC 59 CO 11,
IEC 704, DIN 45635 Part 21, NFS 31-031
(84/538/EEC).
The value of the vibrations emitted on the hand is
3,8 m/s 2 . This value was determined in compliance
with EN 786 Appendix D: 1996+A1: 2001.
Tool runs
on!
230V ~ 50 Hz
500 W
ø 32 cm
11,000 rpm
ø 1.2 mm
84 dB(A)
96 dB(A)
3,8 m/s 2
2,9 kg