Multiplex MULTIcont MSB EXPERT 20 Notice D'utilisation page 11

7.7. P S
ROGRAMMING
MPX L
AND AUNCHER
Programming Transmitter
stick
Battery LiPo / LiFe
Brake on / off
Reverse on / off
Motor cut-off hard / reduce
Motor start soft / normal
Timing auto / manual
Pulse frequency hard 22 - 30° /
soft 7°
Model type heli / fixed-wing
Sensor display / no / no / no
warning
thresholds /
alarms
7.8. P
ROGRAMMING MOTOR FUNCTIONS IN STICK
:
MODE
Beeps indicate the status of programming when using the
transmitter stick, and also confirm any changes. The procedure
runs through all variable parameters step by step. You select the
desired programming option by moving the throttle stick either to
the full-throttle or motor OFF position. Returning the stick to
centre takes you on to the next programmable parameter.
0.
Activate programming mode
0.1 Flight battery disconnected
Stick to full-throttle position
Transmitter ON
0.2 Connect fully-charged flight
battery
0.3 Stick to centre position
0.4 Stick to full-throttle position
0.5 Stick to centre position
1. Select battery mode
(single beep, continuously repeated)
1.1 Automatic low-voltage cut-
off for LiPo batteries*
→
stick to full-throttle
position
OR:
For LiFePo batteries
→
stick to motor OFF
position
1.2 Stick to centre position
Operating Instructions
MSB EXPERT
- S / MULTI
UMMARY TICK
MULTImate/Launcher
LiPo / LiFe / other
on / off
on / off
hard / reduce / ignore
soft / normal
auto / manual
hard 22 - 30° / soft 7°
heli / fixed-wing
yes / yes / yes
⇒ Rising tone sequence
⇒ In LiPo mode:
Indicates detected LiPo
cell count
⇒ in LiFePo mode the
following signal is emitted
immediately
⇒ Rising tone sequence
⇒ Rising tone sequence
⇒ Rising tone sequence
⇒ Rising tone sequence
sounds four times: the
controller is now in
programming mode
⇒ Long tone
(confirmation signal)
MULTIcont
20 / 40 / 60 / 80
MATE
2. Select brake mode
(double beep, continuously repeated)
2.1 For brake ON*
→
stick to full-throttle
position
OR:
For brake OFF
→
stick to motor OFF
position
2.2 Stick to centre position
3. Select direction of rotation
(triple beep, continuously repeated)
3.1 For reverse rotation
→
stick to full-throttle
position
OR:
For standard rotation*
→
stick to motor OFF
position
3.2 Stick to centre position
-
4. Select motor cut-off type
(quadruple beep, continuously repeated)
4.1 For motor cut
(hard stop)
→
stick to full-
throttle position
OR:
For power
reduction *
→
stick to motor
OFF position
4.2 Stick to centre
position
5. Select motor start-up behaviour
(five-times beep, continuously repeated)
5.1 For soft-start *
→ stick to full-throttle
position
OR:
For standard start-up
→ stick to motor OFF
position
5.2 Stick to centre position
Seite 4 von 32
⇒ Confirmation signal
emitted
⇒ Confirmation signal
emitted
⇒ Confirmation signal emitted
LiPo batteries:
Motor off at 3.0 V / cell
LiFePo batteries:
Motor off at 2,5 V!
LiPo batteries:
Motor speed is reduced at 3.2 V /
cell throttle stick to motor OFF
position open throttle
completely at 2.9 V / cell
NiXX batteries:
This setting is only available using
the MULTImate or MPX Launcher
⇒ Confirmation signal
emitted
Motor start-up time in
helicopter mode:
approx. 7.0 sec
in fixed-wing mode:
approx. 1.3 sec
Motor start-up time in
helicopter mode:
approx. 2.0 sec
in fixed-wing mode:
approx. 0.2 sec
motor off