Jenn-Air PRO-STYLE JDRP848HL Guide D'utilisation Et D'entretien page 17

BEHAVIOR
START Button - Invalid
Selection (Quick Blink)
Temperature/Mode Knob -
Invalid Selection
(Quick Blink)
Prompt for Action -
Inactivity (Quick Blink)
Validity Check Delay
Invalid Temperature
Selection Made During A
Cycle
Changing Mode Selections
During A Cycle
Changing Temperature
Selections During A Cycle
A tone will sound when:
the unit is powered on
■
the unit switches to Off mode
■
a valid Mode and Temperature selection has been made and
■
the Start button is pressed to begin a cycle
an invalid Start button selection is made
■
there is an error with the unit
■
DESCRIPTION/EXAMPLES
If an invalid knob combination has been chosen and
the Start Button is pressed, the Start Button Indicator
Light will quickly blink and a tone will sound to
indicate that the chosen selection is invalid.
See "Knob Combinations" table for examples.
If an invalid knob combination has been chosen, the
Mode Knob Indicator Light and Temperature Knob
Indicator Light will quickly blink white. The indicator
light will continue to quickly blink and a tone will
sound every 30 seconds until the error is fixed or
timeout after 2 minutes of inactivity.
See "Knob Combinations" table for examples.
When a valid knob combination has been made, the
Start button indicator light will quickly blink to prompt
for the Start button to be pressed.
If no action is taken after 2 minutes, a tone will sound
and the unit will timeout and return to idle mode.
To exit the unit from idle mode, reselect a Mode and
Temperature Knob selection before pressing the Start
button.
The unit goes through a validity check to verify that
the selected Mode and Temperature combination is
valid.
If a valid combination has been selected, the
Mode/Temperature Knob indicator lights will
show white and the Start button will begin to blink
prompting for action.
If an invalid combination has been selected, the knob
indicator lights will blink to show that the selected
Mode and Temperature combination is invalid.
If the Temperature Knob is changed during a cycle
to a selection that is invalid and the unit was in a
previous cycle, the unit will remain in the previous
cycle until corrected.
The knob indicator lights will blink to show an invalid
selection has been made and will continue to light
until corrected.
If the Mode Knob is changed during a cycle to a
selection that is valid, the Start button will blink to
indicate prompt for action. Press the Start Button to
begin new Mode selection.
If the Temperature Knob is changed during a cycle
to a selection that is valid, the temperature will
automatically change.
USING YOUR OVEN
EXAMPLES
Bake on the Mode Knob and Wi-Fi on the
Temperature Knob.
HOW TO START OVEN
1. Set mode and temperature knobs to
desired selection.
NOTE: The Start button will blink white
when ready.
2. Press the Start button to begin cycle.
Bake on the Mode Knob and Wi-Fi on the
Temperature Knob.
HOW TO START OVEN
1. Set mode and temperature knobs to
desired selection.
NOTE: The Start button will blink white
when ready.
2. Press the Start button to begin cycle.
A quick blink indicates that a valid
combination has been selected and is
prompting for an action to be taken i.e.
Mode is in Bake and temperature is at 350oF
(177oC), but the Start button has not been
pressed yet.
Refer to "Knob Combinations" section for
more information.
If the Start Button is pressed too quickly in
the validity check, the Start Button indicator
light will display an invalid quick blink.
Mode is in bake, temp is at 350oF (177oC), the
Start button is pressed and cycle is running.
Then temp is moved to clean. Unit will
continue to bake at 350oF (177oC).
If the Mode Knob is moved from Bake to
Convect Bake, the Start button will blink as a
prompt for action.
If the temp during a Bake cycle is moved from
350oF to 450oF (177oC to 232oC), the unit will
bake at 450oF (232oC).
preheating has been completed
■
the timer from the app has ended (the tone will sound every
■
five minutes until the timer is stopped)
a Wi-Fi event is occurring
■
the Meat probe connects/disconnects
■
17