Publicité
Rinse aid and refined salt
Only use products which have been specifically designed
EN
for dishwashers.
Do not use table salt or industrial salt, or washing up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to any
add rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard or
(Follow the instructions given on the packaging).
very hard.
If you do not add salt or rinse aid, the LOW SALT
LOW RINSE AID indicator lights will remain lit.
Measuring out the rinse aid
off surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
is illuminated, a reserve supply of rinse aid is still available
on the lid;
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
Rinse-aid dispenser setting
If you are not completely satisfied with the drying results, you
the P
indicator light of the set level flashes (set to factory level)
Adjust the level of rinse aid supply using the P button; during
this procedure the rinse aid indicator light flashes.
Press the ON/OFF button to save the setting.
you run out of rinse aid.
Up to maximum 4 levels can be set based on the dishwasher
model.
adjustment device to a higher number (3-4.)
Setting the water hardness
using refined salt specially designed for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.
26
All manuals and user guides at all-guides.com
*
indicator light on the control panel
"D"
by pressing and pulling up the tab
Press and hold the P button for a few seconds until you hear
button, the indicator light of the set level flashes
set to medium
level).
During this procedure the salt indicator light flashes.
Adjust the hardness level using the P button,
hardness table)
up to max. 4
Press the ON/OFF button to save the setting.
*
and
still be filled.
Water Hardness Table
level
°dH
1
0 - 11
2
12 - 17
3
17 - 34
*
34 - 50
4
*
**
Measuring out the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
the cap of the salt dispenser;
*
is illuminated
salt residues away from the opening; rinse the cap under running
water and then screw it on, the head facing downwards so as to
let the water flow out of the four slots (star-shaped) on the lower
part of the cap (cap with green float
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
so that any saline solution which has leaked out of the salt
dispenser is removed.
*
Only available in selected models.
(water softener
*
levels.
Average salt container
capacity duration
°fH
mmol/l
months
0 - 20
1,1 - 2
21 - 30
2,1 - 3
31 - 60
3,1 - 6
61 - 90
6,1 - 9
*
cannot be seen by simply looking at
;
unscrew the cap (anticlockwise).
water tank right up to its edge.
3. Position the funnel
and fill the salt dispenser up to the
normal for a little water to leak out.
*
).
*
see water
**
*
(see figure)
Publicité
