Panasonic WV-CP290 Mode D'emploi page 15

6 6
Turn on the power. Turn on the power.
WV-CP290 WV-CP290
The included power cord is connected to this power connector. The included power cord is connected to this power connector.
Connect between the power connector on the rear side of the camera and a plug socket Connect between the power connector on the rear side of the camera and a plug socket
with the supplied power cord. with the supplied power cord.
120 V AC, 120 V AC,
60 Hz 60 Hz
Caution: Caution:
• The camera shall be connected with cord set with plug. • The camera shall be connected with cord set with plug.
Plug for respective country shall be mounted on the Plug for respective country shall be mounted on the
Power cord by a qualified electrical. Power cord by a qualified electrical.
WV-CP294 WV-CP294
Important: Important:
• The power supply of 24 V AC/12 V DC shall • The power supply of 24 V AC/12 V DC shall
be insulated against 120 V AC. be insulated against 120 V AC.
• The power supply is automatically select- • The power supply is automatically select-
ed either 24 V AC or 12 V DC. No setting is ed either 24 V AC or 12 V DC. No setting is
required with this camera. required with this camera.
A Loosen the screw of the power cord plug A Loosen the screw of the power cord plug
(accessory). (accessory).
B Connect the power supply (option) of 24 V B Connect the power supply (option) of 24 V
AC or 12 V DC to the power cord plug. AC or 12 V DC to the power cord plug.
Strip the end of the wire by 3 mm to 7 mm Strip the end of the wire by 3 mm to 7 mm
{1/8" to 1/4"}, and twist the stripped part of {1/8" to 1/4"}, and twist the stripped part of
the wire sufficiently to avoid short circuit. the wire sufficiently to avoid short circuit.
• Specification of cable (wire) • Specification of cable (wire)
AWG #16 - #28, Single core, twisted AWG #16 - #28, Single core, twisted
* * Check whether the stripped part of the Check whether the stripped part of the
wire is not exposed and is securely con- wire is not exposed and is securely con-
nected. nected.
<Ratings> <Ratings>
24 V AC 24 V AC
A A 2-N 2-N
B B GND GND
C C 1-L 1-L
C Tighten the screw of the power cord plug. C Tighten the screw of the power cord plug.
D Connect the power cord plug to the AC/DC D Connect the power cord plug to the AC/DC
power terminal on the rear side of the cam- power terminal on the rear side of the cam-
era. era.
* Make sure that the power cord plug is insert- * Make sure that the power cord plug is insert-
ed fully into the AC/DC power supply termi- ed fully into the AC/DC power supply termi-
nal. nal.
All manuals and user guides at all-guides.com
Power cord (accessory) Power cord (accessory)
12 V DC 12 V DC
(GND) (GND)
NC NC
BS BS . . . .
D/ N D/ N BLC BLC
ON ON ATW ATW
ON ON ON ON INT INT
OFF OFF OFF OFF LL LL
OFF OFF AWC AWC
VIDEO VIDEO OUT OUT
  120V ~ 60 Hz 120V ~ 60 Hz
B. S. B. S.
D/ N D/ N BLC BLC
ON ON ATW ATW
ON ON ON ON INT INT
OF F OF F OF F OF F LL LL
OF F OF F AW C AW C
24 V 24 V I N I N
VIDEO VIDEO OUT OUT
~ ~
1- L 1- L 2- N 2- N
GND GND
12 V 12 V I N I N
NC NC
To 24 V AC/12 V DC To 24 V AC/12 V DC
power supply power supply
Power cord plug Power cord plug
(accessory) (accessory)
Stripped Stripped
3 mm - 7 mm 3 mm - 7 mm
{1/8" to 1/4"} {1/8" to 1/4"}
15 15