Publicité
Proper Hand Position (Fig. B)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the tool body
with the other hand on the neck of the die grinder
in Figure B.
Instructions for Use (Fig. A–C)
WARNING:
•
Ensure all materials to be ground or cut are secured
in place.
•
Use clamps or a vice to hold and support the
workpiece to a stable platform. It is important to
clamp and support the workpiece securely to prevent
the movement of the workpiece and loss of control.
Movement of the workpiece or loss of control may
create a hazard and cause personal injury.
•
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
•
Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
•
Always wear regular working gloves while operating
this tool.
•
The gear case becomes very hot during use.
•
Apply only a gentle pressure to the tool. Do not exert
side pressure on the disc.
•
Avoid overloading. Should the tool become hot, let it
run a few minutes under no load condition.
•
The best grinding results are achieved when setting
the machine at an angle of 90°. Move the machine
back and forth with moderate pressure. In this
manner, the workpiece will not become too hot, does
not discolour and no grooves are formed.
WARNING: Grasp tool firmly with both hands to maintain
control of the tool at start up and during use and until the
wheel or accessory stops rotating. Make sure the accessory
has come to a complete stop be fore laying the tool down.
Put the work in a vise or clamp it securely. Use a face mask
over the nose and mouth if the operation raises dust. Treat
the wheel with respect. Do not jam the wheel into the work or
use unnecessary pressure. Grind only on the face of the wheel
unless you have a special wheel specifically made to permit
grinding on the side of the wheel.
Paddle Switch (Fig. A)
CAUTION: Hold the neck and the body of the tool firmly
to maintain control of the tool at start up and during use
All manuals and user guides at all-guides.com
12
,
as shown
13
and until the wheel or accessory stops rotating. Make sure
the accessory has come to a complete stop be fore laying
the tool down.
CAUTION: Before connecting the tool to a power source
depress and release the paddle switch
that the switch is off. Depress and release the paddle
switch as described above after any interruption in power
supply to the tool, such as the activation of a ground
fault interrupter, throwing of a circuit breaker, accidental
unplugging, or power failure.
nOTE: To reduce unexpected tool movement, do not switch
the tool on or off while under load conditions. Allow the grinder
to run up to full speed before touching the work surface. Lift the
tool from the surface before turning the tool off. Allow the tool
to stop rotating before putting it down.
1. To turn the tool on, push the lock-off lever
back of the tool, then depress the paddle switch
will run while the switch is depressed.
2. Turn the tool off by releasing the paddle switch.
LED Worklight (Fig. A)
CAUTION: Do not stare into worklight. Serious eye
injury could result.
The worklight
11
located around the collet is activated as soon
as the tool is powered. The worklight will stay illuminated as
long as the tool is powered.
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Spindle Lock (Fig. A)
The spindle lock
2
is provided to prevent the spindle from
rotating when installing or removing accessories. Operate the
spindle lock only when the tool is turned off, unplugged from
the power supply, and has come to a complete stop.
NOTICE: To reduce the risk of damage to the tool, do
not engage the spindle lock while the tool is operating.
Damage to the tool will result and attached accessory
may spin off possibly resulting in injury.
To engage the lock, depress the spindle lock button and
rotate the spindle by hand until you are unable to rotate the
spindle further.
Precautions To Take When Working on a
Painted Workpiece
1. Sanding or wire brushing of lead based paint is NOT
RECOMMENDED due to the difficulty of controlling the
contaminated dust. The greatest danger of lead poisoning is
to children and pregnant women.
2. Since it is difficult to identify whether or not a paint contains
lead without a chemical analysis, we recommend the
following precautions when sanding any paint:
Personal Safety
1. No children or pregnant women should enter the work area
where the paint sanding or wire brushing is being done
until all clean up is completed.
English
7
once to ensure
8
toward the
7
. The tool
7
Publicité
