Laserworld Club Serie Mode D'emploi page 6

Manual: CS-12.000RGB SN - CS-24.000RGB SN
fessional associations and/or comparable
regulations for accident prevention.
10. If the device has been exposed to great
temperature changes, do not switch it
on immediately. Condensation (or any
moisture/water formed) may damage
this device.
11. Never use dimmer, RC or other electroni-
cally switched sockets. Whenever possib-
le, do not use the laser projector together
with large appliances (especially fog ma-
4. Working on the device
1. This product has no user serviceable parts inside and should
only be maintained and serviced by a qualified engineer.
2. Be sure that the mains plug is not connected to the power
supply while installing the device.
3. Take off all reflecting things like rings, watches, etc.
before starting to work with or at the projector.
4. Only use non-reflecting tools to work on device.
5. Warning concerning back reflection:
• Semiconductor laser sources (diodes) are by their nature particularly sensitive to back
reflections. Direct or diffused laser radiation from external laser sources can lead to the
irreversible extinction / damage of individual or all laser diodes in a projector.
• Under no circumstances should a laser projector project a laser beam directly into an
opposing projector at the same time. It is up to the user to determine either the ori-
entation / position of the devices or to adapt the programming in such a way that two
opposite projectors do not shoot into each other.
6. Wear protective clothing (like goggles, gloves etc.) according to laser power and wave-
length of the laser.
5. Service notes
• Moisture and heat can reduce lifetime of
the laser system dramatically and expires
any warranty claim.
• Quick on/off switching of this device will
reduce durability of the laser diode dra-
matically.
• Avoid sharp knocks and shocks to this
device an endsure sufficient protection
page 10 / 28
chines) on the same mains!
12. Ensure sufficient ventilation and do not
place the device on any warm or heat ra-
diating surface. Especially the ventilati-
on openings must not be covered!
13. Ensure that device does not get over-
heated. Make sure that the device is not
exposed to spotlights (especially moving
heads). Heat of spotlights could overheat
laser in a little while and leads to a degra-
dation of performance.
during transportation. Look after your
Laserworld product.
• To increase durability of your laser,
protect device against overheating:
-
Always ensure sufficient ventilation.
-
Do not face spotlights (especially mo-
ving heads) to the device.
English
-
Check temperature after approx. 30
minutes with each new installation.
If necessary install the projector at a
place with different temperatures.
-
Keep the device dry. Protect it from
moisture, rain and damp.
-
Switch off device when it is not nee-
ded. Diodes are switched on and can
wear out even if there is no visible la-
ser output.
• Please ensure the fans and heatsinks are
clear from dust and debris otherwise the
risk of overheating may occur. If the unit
or air inlets appear to be blocked, please
contact a qualified service engineer to
6. General Operation
1. Power
Connect the power cord to the device and to the mains. Make sure that your device is pro-
vided with the correct voltage. Wrong voltage could lead to irreparable damages. Please
find the correct voltage data in the synoptical table at the end of this manual. Make sure
that the device is not directed to people or inflammable objects during installation. To
start the device, connect the interlock bridge, insert the key and switch it on, and switch
the device on. The "Emission - Laser on" LED at the front side of the device begins to
light up when the device is ready for use.
2. Key Switch
There is a key switch at the back of the laser system. Please plug the key to the switch and
turn it on. The laser device only runs when the key is inserted and switched on. Prevent
misuse! Unplug the key when the laser is unattended to prevent misuse of the sys-
tem.
3. Fuse
There is a fuse at the back side of the device. If the fuse should blow, please exchange
it with a new one. If the problems recurs, please contact your dealer or the Laserworld
service department.
4. Safety Presets
This device has an integrated Scan Safety (SFS). Is the Scan Safety active (on), single be-
ams are prevented. If the Scan Safety is switched off, it is possible to create full power
single beams - be careful!.
Operating the laser system with disabled SFS may not be allowed in some countries.
Always ensure that maximum permissible exposure (MPE) is not exceeded in areas
accessible to the public or members of staff.
English
Manual: CS-12.000RGB SN - CS-24.000RGB SN
maintain and service the product.
• Always place the laser behind fog machi-
nes and hazers
• Avoid direct exposure of the laser to
moisture
• Clean the exit window with glass cleaner
from time to time
Removal of the warranty label as well
•
as damages to the device caused by
improper handling, neglect of the sa-
fety instructions and service notes will
void the warranty.
page 11 / 28