Bosch GWS 19-125 CI Professional Notice Originale page 25

Speed preselection
(GWS 19-125 CIE)
You can preselect the required speed using the speed preselection thumbwheel (4), even during operation. The information in
the table below describes the recommended values.
Material Application
Metal Removing paint
Metal Brushing, removing rust
Stainless steel Grinding
Metal Rough grinding
Metal Cutting
Stone Cutting
The rated speed of the accessory must be at least
u
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
Level GWS 19-125 CIE
Speed preselection [min
1 2800
2 4500
3 6300
4 8200
5 9800
6 11,500
The values specified for speed levels are guide values.
Fitting
Fitting Protective Equipment
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard (8) onto
the holder on the power tool until the
coding cams of the protective guard
are aligned with the holder. When do-
ing so, press and hold the unlocking
lever (1).
Press the protective guard (8) onto
the spindle collar until the shoulder of
the protective guard is sitting on the
flange of the power tool and rotate the
protective guard until it audibly clicks
into place.
Adjust the position of the protective guard (8) to meet the
requirements of the operation. To do this, push the unlock-
Bosch Power Tools
Application tool
Sanding sheet
Cup brush, abrasive disc
Grinding disc/fibre disc
Grinding disc
Cutting disc
Diamond cutting disc
ing lever (1) upward and rotate the protective guard (8) into
the required position.
u
u
-1
]
u
Note: The coding cams on the protective guard (8) ensure
that only a protective guard that is suitable for the power
tool can be fitted.
Extraction guard for sanding
For low-dust grinding of paints, lacquers and plastics in con-
junction with carbide grinding heads (11), you can use the
extraction guard (9). The extraction guard (9) is not suitable
for machining metal.
A suitable Bosch dust extractor can be connected to the ex-
traction guard (9). To do so, insert the vacuum hose with
dust extraction adapter into the provided receiving connec-
tion of the extraction guard.
Protective guard for cutting
u
u
The protective guard for cutting (7) is fitted in the same way
as the protective guard for grinding (8).
Metal cover for cutting
Fit the metal cover for cutting (27) on the protective guard
for grinding (8) (see figure A): Swivel the tool retainer back
(➊). Attach the cover (27) to the protective guard for
grinding (8) (➋). Press the tool retainer firmly into place on
the protective guard (8) (➌).
To remove the cover (see figure B), press the button on the
tool retainer (➊) and swivel it back (➋). Remove the
cover (27) from the protective guard (8) (➌).
Thumbwheel position
2–3
3
4–6
6
6
6
Always position the protective guard (8) such that the
two cams on the unlocking lever (1) engage in the
corresponding openings on the protective guard (8).
Adjust the protective guard (8) such that sparking in
the direction of the operator is prevented.
The protective guard (8) must only be able to be ro-
tated in the direction of the accessory while the un-
locking lever (1) is actuated. Otherwise, the power
tool must not be used any more under any circum-
stances and must be sent to the after-sales service.
For cutting, always use the protective guard for
cutting (7) or the protective guard for grinding (8) to-
gether with the cover for cutting (27).
Provide sufficient dust extraction when cutting stone.
1 609 92A 5RE | (16.01.2024)
English | 25