Publicité
10 | Français
Kickback Control
If there is a sudden kickback in the power tool,
e.g. jamming when carving, the power supply
to the motor will be interrupted electronically.
To restart the tool, set the on/off switch (5)/
(11) to the "off" position and then switch the power tool on
again.
Restart Protection
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
To restart the tool, set the on/off switch (5)/(11) to the
"off" position and then switch the power tool on again.
Note: Rapidly switching the power tool off and on again may
trigger the restart protection, meaning the power tool may
not start up even if the on/off switch (5)/(11) is pressed.
Set the on/off switch (5)/(11) to the off position and then
switch the power tool on again.
Soft start
The electronic soft start limits the torque when the power
tool is switched on and increases the service life of the mo-
tor.
Practical advice
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Protect the grinding tools against impact.
u
Do not load the power tool so heavily that it comes to a
u
stop.
If the power tool has been subjected to a heavy load,
u
continue to run it at no-load for several minutes to
cool down the accessory.
Grinding tools can become very hot while working. Do
u
not touch them until they have cooled down.
Move the grinding tool evenly back and forth with light pres-
sure to achieve an optimum work result. Pressure that is too
strong reduces the performance capability of the power tool
and causes the grinding tool to wear more quickly.
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In extreme conditions, always use a dust extractor if
u
possible. Blow out ventilation slots frequently and in-
stall a residual current device (RCD) upstream. When
machining metals, conductive dust can settle inside the
power tool, which can affect its protective insulation.
Store and handle the accessories carefully.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
1 609 92A A80 | (25.11.2024)
after-sales service centre that is authorised to repair Bosch
power tools.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Disposal
The power tool, accessories and packaging should be re-
cycled in an environmentally friendly manner.
Do not dispose of power tools along with
household waste.
Français
Consignes de sécurité
Avertissements de sécurité généraux pour l'outil
Lire tous les avertissements de sé-
AVERTISSE-
curité et toutes les instructions.
MENT
Ne pas suivre les avertissements et
instructions peut donner lieu à un choc électrique, un incen-
die et/ou une blessure sérieuse.
Conserver tous les avertissements et toutes les instruc-
tions pour pouvoir s'y reporter ultérieurement.
Le terme «outil» dans les avertissements fait référence à
votre outil électrique alimenté par le secteur (avec cordon
d'alimentation) ou votre outil fonctionnant sur batterie (sans
cordon d'alimentation).
Bosch Power Tools
Publicité
