Publicité
English
3. Empty contents of dust tank
or drain.
CAUTION: Clean the water level limiting device
regularly and examine it for signs of damage. Refer to
Fig. G.
NOTICE: DO NOT remove ball oat
will cause damage to the vacuum. The ball oat keeps
water from entering the motor.
Before using the vacuum for wet pick up:
• Ensure the dust tank is empty and free of excessive dust.
• Remove the lter
.
9
TO CONVERT BACK TO DRY VACUUM
OPERATION (Fig. A)
1. Empty dust tank, refer to TO EMPTY DUST TANK
instructions.
2. Place dust tank upside down position until dry. DO
NOT use wet dust tank for dry pick up.
3. Place vacuum head
on a level surface appliance dry.
4
4. Reinstall lters when vacuum head is dry.
See Filters under Maintenance.
5. When dust tank is dry place the vacuum head
onto the dust tank and secure it by closing the
lid latches
.
5
SHUT DOWN/TRANSPORTATION (Fig. A)
1. Turn on/off switch
3
2. Unplug the unit.
2
3. Store the power cord
handle/cord wrap
as shown.
1
4. When transporting in vehicles, secure the machine.
MAINTENANCE
The D
WALT appliance has been designed to operate
E
overall long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper appliance care and regular
cleaning.
WARNING: To reduce the risk of injury,
turn appliance off and disconnect
appliance from power source before
installing and removing accessories,
before adjusting or changing set-ups or
when making repairs. An accidental start-up
can cause injury.
WARNING: For user servicing, the machine must
be dismantled, cleaned and serviced, as far as is
reasonably practicable, without causing risk to the
maintenance staff and others. Suitable precautions
include, decontamination before dismantling, provision
for local ltered exhaust ventilation where the machine
is dismantled, cleaning of the maintenance area and
suitable personal protection.
• The manufacturer, or an instructed person, shall
perform a technical inspection at least annually,
consisting of, for example, inspection of the lter for
damage, air tightness of the machine and proper
function of the control mechanism.
into a suitable container
6
, doing so
14
4
to the OFF position.
wrapping it around the top
• When carrying out service or repair operations, all
contaminated items which cannot be satisfactorily
cleaned, are to be disposed of; such items shall be
disposed of in impervious bags in accordance with
any current regulation for the disposal of such waste.
• For dust extractors it is necessary to provide for an
adequate air change rate L in the room if the exhaust
air is returned to the room.
NOTE: Refer to national regulations is necessary.
FILTER (Fig. A, H, I)
FILTER CARE
The lters included with this vacuum are long life lters.
To be effective in minimizing dust recirculation, the lters
MUST be installed correctly and in good condition.
WARNING: Appropriate personal protective
equipment like dust mask and gloves should be used
while handling the lters.
To Remove Clean Connect Filter
1. Turn on/off switch
and unplug cord from outlet.
2. Release lid latches
head
from canister. Place vacuum head on a
4
level surface upside down.
3. Turn each lter
counterclockwise by gripping it
9
on the plastic end cover as shown, and carefully
remove from head, ensuring debris does not fall into
mounting hole.
NOTE: Use care to not damage lter material.
4. If the bottom side of the vacuum head
be cleaned, use a cloth dampened with water and
mild soap and allow it to dry. Dispose the cloth in an
appropriate container.
5. Inspect lters for wear, tears or other damage.
NOTE: If there is any doubt on the condition of the
lters they MUST be replaced. DO NOT continue use
if lters are damaged.
WARNING: Never use compressed air or a brush
to clean lters, otherwise damage to the lter membrane
will occur which will allow dust to pass through the lter.
If needed, gently tap against a hard surface or rinse with
room temperature water and let air dry. Cleaning of the
lters is typically unnecessary, even if the lter is covered
with dust. The automatic lter cleaning system will
maintain maximum performance and continue to function.
If visual damage to the lter membrane exists, replace
lters. Filters typically last between six and twelve months
depending on use and care.
To Install Clean Connect Filter
1. Ensure lter seal
15
2. Line up lter threads
using moderate force, turn lter clockwise until tight.
NOTE: Use careful to not damage lter material.
3. Place the vacuum head
secure it by closing the lid latches
18
TM
to the OFF position ( O )
3
and remove vacuum
5
needs to
4
TM
is in place and is secure.
to vacuum head threads and
16
onto the dust tank and
4
.
5
Publicité
