Publicité
English
IMPORTANT SAFEGUARDS
The symbol on the product or packaging indicates that
the product must not be treated as domestic refuse.
Instead, it should be handed in to a collection point for
the recycling of electrical and electronic components.
By ensuring the product is treated in the right way, this
will help to prevent the negative impact on environment
and health that may result from the product being thrown
away as general waste. For further information about
recycling, you should contact the local authorities, refuse
collection service or the sales outlet where you bought
the goods.
PROTECTING THE ENVIRONMENT
Separate collection. Products and batteries
marked with this symbol must not be
disposed of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and
batteries according to local provisions. Further
information is available at www.2helpU.com
DESCRIPTION (Fig. A)
WARNING : Never modify the power appliance or
any part of it. Damage or personal injury could result.
Top handle/cord wrap
1
Power cord
2
On/off switch
3
Vacuum head
4
Lid latches
5
Dust tank
6
Hose
7
Casters
8
Clean Connect
lter
9
TM
Vacuum port
10
Hose strap
11
Disposable dust bag
12
ASSEMBLY AND ADJUSTMENTS (Fig. A–C)
WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing
set-ups or when making repairs. An accidental
start-up can cause injury.
WARNING: The lter
place while vacuuming, except as described
under WET PICK UP APPLICATIONS under
OPERATION. When vacuuming ne dust, you
may also need to use an disposable dust bag to
make emptying the dust tank easier.
must always be in
9
1. Install the disposable dust bag
in Fig. B.
NOTE: Be careful not to tear the bag. Place bag
securely onto vacuum port
seal for maximum dust collection performance.
2. Place the vacuum head
secure it by closing the lid latches
3. Insert the end of hose
port
and tighten the end of hose to the tank.
10
OPERATION
INSTRUCTIONS FOR USE (Fig. A, D, E)
WARNING: Always observe the safety instructions
and applicable regulations.
1. Plug the power cord into an appropriate outlet.
2. Turn the on/off switch
3. The D
WALT construction dust extractor is tted
E
with the D
WALT connection system. It allows a
E
fast, secure connection between the hose
and power tool. The connector
directly to D
WALT compatible tools or through the
E
use of an adapter (available from local D
supplier). If you need to Install the adapters, refer to
Fig. E.
NOTE: If using an adapter ensure it is rmly
attached to the tool outlet before following the steps
below.
OPERATING INSTRUCTIONS
CASTER INSTALLATION (Fig. A, F)
1. Invert the dust tank and install the casters to the
bottom of the dust tank and x them with screws.
2. Return dust tank assembly upright.
REMOVE/CHANGE USED DISPOSABLE
DUST BAG (Fig. A)
WARNING: Appropriate personal protective
equipment like dust mask and gloves should be used
while handling used dust bags.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
5
3. Pull the disposable dust bag
port
.
10
4. Seal the disposable dust bag
removing it from the machine.
5. Dispose the disposable dust bag
container according to statutory provisions.
WET PICK UP APPLICATIONS (Fig. A, G)
WARNING: If foam or liquid escapes from the
machine,switch off immediately.
WARNING: Do not use the machine with this set
up for dust Class L.
The ball oat
will block air to the motor when
14
the dust tank is full and the sound of the motor will
change at once.
When the motor has a high pitched sound and air/
water ow stops, empty the dust tank.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
5
head
.
4
17
, as shown
12
to provide a tight
10
onto the dust tank and
4
.
5
into clip-in hose vacuum
7
to the ON position ( I ).
3
7
connects
13
WALT
E
and remove vacuum head
carefully from vacuum
12
opening tightly when
12
in appropriate
12
and remove vacuum
4
.
Publicité
