EINHELL TP-AG 18/125 F Li BL Instructions D'origine page 20

•
Do this by simply turning the guard (4) into
the required position.
•
No additional fastening of the guard (4) is
needed.
•
The guard (4) cannot be removed from the
tool.
5.3 Fitting/removing the cutting wheel guard
(Fig. 4-6 / Item 7)
•
The angle grinder is equipped with a remo-
vable cutting wheel guard (7).
•
The guard (4) does not need to be replaced
in order for you to fit the cutting wheel guard.
•
Beginning from the end with the lug (Fig. 4/
Item f), push the removable cutting wheel gu-
ard (7) onto the guard.
•
Make sure when doing so that the guard (4)
lies between the guide ribs of the removable
cutting wheel guard (Fig. 4).
•
Then push the removable cutting wheel guard
counter-clockwise onto the guard until you
hear this guard latch in place (Fig. 5a-5c).
•
To take off the removable cutting wheel guard
(7) again, press the lug (f) slightly away from
the guard (4) as shown in Fig. 6 until you can
rotate the removable cutting wheel guard (7).
Now turn the cutting wheel guard clockwise
and off the guard (4).
6. Operation
6.1 Charging the Li battery pack (Fig. 1a-1b)
1. Remove the battery pack (a) from the handle,
pressing the pushlock button (b) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(c) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
Anl_TP_AG_18_125_F_Li_BL_SPK13.indb 20 Anl_TP_AG_18_125_F_Li_BL_SPK13.indb 20
GB
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Switching on (Fig. 7)
To start the equipment, push the On/Off switch
(2) forwards and press it down. To switch off the
angle grinder, depress the On/Off switch (2) at the
back. The On/Off switch (2) will jump back into its
starting position.
Important!
The equipment switches to "Standby Mode" after
10 minutes of non-use.
To reactivate: Switch on the equipment twice or
press the battery capacity indicator.
"Standby Mode" protects the battery.
Important!
Following a stoppage (due to overloading), the
cordless equipment starts up again automatically.
Important!
Wait until the machine has reached its top
speed. You can then position the angle grin-
der on the workpiece and machine it.
6.3 Battery capacity indicator (Fig. 1c/Item d)
Press the battery capacity indicator switch (e).
The battery capacity indicator (d) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
- 20 -
04.06.2024 11:16:41 04.06.2024 11:16:41