Publicité
Basic Function Operation
Auto Mode Operation
1. Set the unit to AUTO mode by pressing the MODE button
until "AUTO" is selected.
2. Use the Up and Down or +/- buttons to choose the desired
temperature.
3. Press the POWER button to turn on the unit. The system will
automatically select cooling or fan-only operation depending
on what temperature is selected and the current room
temperature.
4. The unit will control the room temperature automatically
based on the set temperature.
NOTE: In this mode, the fan speed cannot be adjusted. It
will be set automatically at a speed according to the room
temperature.
Cool or Heat Mode Operation
1. Set the unit to COOL/HEAT mode by pressing the MODE
button until "COOL" is selected
2. Use the Up and Down or +/- buttons to choose the desired
temperature.
3. Adjust the fan speed by the FAN button.
4. Press the POWER button to turn on the unit.
Fan Mode Operation
1. Set the unit to FAN mode by pressing the MODE button until
"FAN" is selected.
2. Adjust the fan speed by pressing the FAN button.
3. Press the POWER button to turn on the unit.
NOTE: This function only provides room air circulation. It does
not provide cooling or allow the temperature to be adjusted.
NOTE: In FAN mode the set temperature is not displayed on
the remote control display screen.
Dry Mode Operation
1. Set the unit to DRY mode by pressing the MODE button until
"DRY" is selected.
2. Use the Up and Down or +/- buttons to choose the desired
temperature.
3. Press the POWER button to turn on the unit.
NOTE: In DRY mode, the unit will operate as a dehumidifier.
Some degree of cooling will continue.
NOTE: In this mode, the fan speed cannot be adjusted. It
will be set automatically at a speed according to the room
temperature.
LED Operation (Remote Only)
1. Press the LED button to turn the LED display on the unit ON
if it is off, and OFF if it is on.
CCD-0008919 Rev: 07.30.24
Advanced Function Operation
GEAR Operation
1. Press the GEAR button. The 75% LED will illuminate. In this
mode, the unit will operate at 75% max current limit.
2. Press the GEAR button again. The 50% LED will illuminate.
In this mode, the unit will operate at 50% max current limit.
3. Press the GEAR button a final time to exit GEAR mode
Sleep Mode Operation
1. Press the Sleep button to initiate the sleep mode. In this
mode the selected temperature will increase (in cooling mode)
by 2°F/1 (or 2)°C 30 minutes after the mode is selected. The
temperature will then increase (in cooling mode) by another
2°F/1 (or 2)°C after an additional 30 minutes. This new
temperature will be maintained for 7 hours before it returns to
the originally selected temperature.
2. After 7 hours, the sleep mode will end and the unit will
continue to operate as originally programmed.
3. The sleep mode program can be canceled at any time
during operation by pressing the SLEEP button again.
Resetting the Filter LED Light/Timer
1. When the Filter LED is illuminated, turn off the unit and clean
the filter.
2. Reinstall the filter, press and hold the SLEEP button for 2
seconds and the LED will turn off.
TURBO Mode Operation
1. Press the Turbo button. The fan will enter TURBO mode to
quickly cool (or heat, based on selected mode) the space.
2. Turbo mode will end automatically when the set temperature
on the unit is reached.
NOTE: Exit TURBO mode manually by pressing the Turbo
button again.
NOTE: Unit consumes more power while in TURBO mode.
Swing Button Operation (Optional, Remote Only)
1. While the unit is ON, press the SWING button to stop the
louver at the desired angle.
Follow Me Operation (Remote Only)
1. While the unit is in AUTO or COOL mode, press the
FOLLOW ME button on the remote.
2. Place the remote in any location where the air temperature
needs to be adjusted. The remote will measure the ambient
temperature at its current location and send it to the unit every
3 minutes.
3. To disable, press the FOLLOW ME button again.
- 16 -
Publicité
