Publicité
ELECTRICAL INSTALLATION
ALL ELECTRIC Laundry Centers
WARNING
The following are specific requirements
for proper and safe electrical installation of your laundry
center. Failure to follow these instructions can create an
electrical shock and/or a fire hazard.
WARNING
This appliance MUST be properly grounded.
Electrical shock can result if the laundry center is not properly
grounded. Follow the instructions in this manual for proper
grounding.
WARNING
Do not use an extension cord with this
laundry center. Some extension cords are not designed to
withstand the amounts of electrical current this laundry center
utilizes and can melt, creating electrical shock and/or fire
hazard. Locate the laundry center within reach of the receptacle
for the length power cord to be purchased, allowing some slack
in the cord. Refer to the pre-installation requirements in this
manual for the proper power cord to be purchased.
WARNING
A U.L. approved strain relief must be
installed onto power cord. If the strain relief is not attached,
the cord can be pulled out of the laundry center and can be
cut by any movement of the cord, resulting in electrical shock.
WARNING
Do nott use an aluminum wired receptacle
with a copper Wired power cord and plug (or vice versa). A
chemical reaction occurs between copper and aluminum and
can cause electrical shorts. The proper wiring and
receptacle is a copper wired power cord with a copper
wired receptacle OR aluminum wired power cord with
an aluminum wired receptacle.
NOTE: Laundry centers operating on a 208 volt power supply
will have longer drying times than laundry centers operating on
a 240 volt power supply.
GROUNDING REQUIREMENTS
Non-Canadian ELECTRIC Laundry Center
WARNING
Improper connection of the equipment
grounding conductor can result in a risk of electrical shock.
Check with a licensed electrician if you are in doubt as to
whether the appliance is properly grounded.
For a grounded, cord-connected laundry center:
1. The laundry center MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk of
electrical shock by a path of least resistance for electrical
current.
2. If your laundry center is equipped with a power supply cord
having an equipment-grounding conductor and a grounding
plug, the plug MUST be plugged into an appropriate, copper
wired receptacle that is properly installed and grounded in
accordance with all local codes and ordinances. If in doubt,
call a licensed electrician.
For a permanently connected laundry center:
The laundry center MUST be connected to a grounded metal,
permanent wiring system; or an equipment grounding con-ductor
MUST be run with the circuit conductors and connected to the
equipment-grounding terminal or lead on the appliance.
ALL GAS Laundry Centers
The laundry center is equipped with a three-prong (grounding)
plug for your protection against shock hazard and should be
plugged directly into a properly grounded three-prong receptacle.
Do not cut or remove thegrounding prong from the plug.
Canadian ELECTRIC Laundry Center
Improper connection of the equipment
DANGER
grounding conductor can result in a risk of electrical shock.
Check with a licensed electrician if you are in doubt as to
whether the appliance is properly grounded.
For a grounded cord connected laundry center:
1. The laundry center MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk of
electrical shock by providing a path of least resistance for
the electrical current.
2. Since your laundry center is equipped with a power supply
cord having an equipment-grounding conductor and a
grounding plug, the plug MUST be plugged into an
appropriate outlet that is properly installed and grounded
in accordance with all codes and ordinances. If in doubt,
call a licensed electrician.
NON-CANADIAN ELECTRIC Laundry Center
ELECTRICAL CONNECTIONS FOR A 3 WIRE SYSTEM
1. Remove the screw securing the
terminal block access cover to the rear
panel and remove cover.
2. Install a U.L. approved strain relief
connector in the entry hole on the back
panel.
3. Insert a NEMA 10-30 Type SRDT, U.L. approved power
cord through the strain relief.
4. Attach the power cord neutral (central wire) conductor to
the silver colored center terminal on the terminal block.
Tighten the screw securely.
GREEN GROUND SCREW
NEUTRAL
GROUND
WIRE
8
SILVER TERMINAL
Publicité
