Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0214
  6. Notice de montage

R&G CP0214 Notice De Montage

Masquer les pouces
1
2
3
4
5
6
7
8
9

Publicité

Liens rapides

Télécharger ce manuel
Page 1 of 9
CP0214
FITTING INSTRUCTIONS CP0214 AERO CRASH PROTECTORS
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

loading

Manuels Connexes pour R&G CP0214

Sommaire des Matières pour R&G CP0214

  • Page 1 Page 1 of 9 CP0214 FITTING INSTRUCTIONS CP0214 AERO CRASH PROTECTORS HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
  • Page 2 Page 2 of 9 CP0214 TOOLS REQUIRED GENERAL TORQUE SETTINGS METRIC HEX KEY BIT M4 BOLT = 8Nm • METRIC A/F SOCKET & WRENCH M5 BOLT = • M6 BOLT = • DRILL & 28mm HOLE SAW M8 BOLT = 20Nm •...
  • Page 3 Page 3 of 9 CP0214 LHS & RHS EXPLODED ASSEMBLY VIEW Before removing engine bolts, ensure the bike is upright and supported by a suitable engine stand or jack placed under the sump of the motorbike to support the partial weight of the engine, this will prevent the engine from moving during fitting.
  • Page 4 Page 4 of 9 CP0214 Remove the existing engine bolt (located middle of the top fairing - can be seen without removing • the fairing) Take M10 x 90mm long bolt and slide washer over it followed by a shake proof washer •...
  • Page 5 Page 5 of 9 CP0214 NOTICE DE MONTAGE CP0214 PROTECTIONS CRASH E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
  • Page 6 Page 6 of 9 CP0214 OUTILS REQUIS VALEURS DE SERRAGE M4 BOULON = 8Nm CLÉ MÉTRIQUE • M5 BOULON = 12Nm CLÉ À CLIQUET + DOUILLES • M6 BOULON = 15Nm • PERCEUSE ET SCIE CLOCHE DE 28mm M8 BOULON = 20Nm CLÉ...
  • Page 7 Page 7 of 9 CP0214 VUE D’ENSEMBLE CÔTÉ GAUCHE ET DROIT DROITE GAUCHE Avant de retirer les boulons du moteur, assurez-vous que la moto soit en position verticale et soutenue par un support moteur ou un cric approprié placé sous le carter de la moto pour supporter le poids partiel du moteur, cela empêchera le moteur de bouger pendant le...
  • Page 8 Page 8 of 9 CP0214 REMARQUE : pour éviter de croiser le filetage, appliquez une pression vers l'avant sur le boulon et faites-le tourner dans le sens inverse des aiguilles d'une montre jusqu'à ce qu'un clic se fasse entendre, puis commencez à tourner dans le sens des aiguilles d'une montre et serrez.
  • Page 9 Page 9 of 9 CP0214 R&G RACING RETURNS POLICY (NON-FAULTY GOODS) Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing.