Publicité
USING THE DAF-320 AS A WIRELESS EXTERNAL ETTL FLASH
(only with cameras supporting the wireless ETTL function)
For most objects, it is of great advantage to use the flash laterally. Illumination will be more pleasant and more balanced than with a frontal flash. For this
purpose, the DAF-320 can be used in wireless TTL flash mode. The wireless TTL flash mode allows you creative illumination of your object with one or
more flash units from various directions. The following information will be useful:
A Master Flash is required to trigger and release the flash or flashes off camera.
Depending on the camera model, the incorporated flash can be used or a flash with master flash function can be used such as the DAF-320.
The DAF-320 can also be removed from the camera and used a Remote Flash. In this case, the flash is remote controlled. You can also use an unlimited
number of DAF-320 as remote flashes. If you work with various remote flashes, you can arrange them into Groups: A, B and C.
You can assign properties to each group. Example: • All flashes of group A will work in TTL flash mode
The number of groups, which can be triggered, and the possible settings vary with the camera model. Please read the instructions of your camera.
Channels: On photo shootings it may happen, that a number of photographers uses same techniques. In order to avoid possible interferences, there are
4 channels available: 1, 2, 3 and 4. It does not matter which channel you use, however, it is important to set both master and remote flashes to the same
channel.
WIRELESS EXTERNAL ETTL FLASH WITH DAF-320 IN MASTER MODUS – HOW TO PROCEED
The DAF-320 in master mode can trigger a number of flashes with remote function (e.g. more DAF-320). The remote flashes are programmed via the
master flash.
1. Press the MODE button for 2 seconds.
2. Using the arrow keys, you can choose between five modes: - Normal ETTL mode
Select Master Mode and confirm with the SET button.
3. The LCD shows a symbol for MASTER, information on groups and the selected channel CH
4. Pressing the SET button, the desired channel can be selected. CH will be marked. Now choose the channel using the arrow keys
and confirm with SET button.
5. In ordert o set the desired flash power ratio between the groups A and be, press the C1 button until the dispaly shows ratio A : B.
Press the SET button to mark the value. Now you can change it using the arrow keys. Confirm your setting using the SET button.
6. Pressing the C1 button again, group C shows up. If you wish to enter a correction value for the flashes of group C, press the SET button until +/- 0
is marked. Now you can set the correction value in steps of 1/3EV using the arrow keys. Confirm your setting using the SET button.
MANUEL FLASH POWER SETTING WITH WIRELESS FLASH (IN MASTER MODE ONLY)
1. Use the C2 button to activate the correction value. The LCD shows +/- 0 marked.
2. Using the arrow keys, you can adjust the flash power in steps of /3EV.
3. Confirm your setting using the SET button.
4. Correction range: -3.0EV to + 3.0EV.
FLASK BRACKETING WITH WIRELESS ETTL FLASH (IN MASTER MODE ONLY)
Press the C2 FEB button twice. Press the C2 button FEB. The gradation symbol is marked in the display. Using the arrow keys, the desired gaps between
the 3 bracketing shots can be set in steps of approx. 1/3 EV. Confirm with SET button.
MANUAL FLASH POWER SETTING WITH WIRELESS FLASH (IN MASTER MODE)
1. Use the MODE button to select the manual power setting "M".
2. Press the C1 button GROUP you can select one or more groups for which the setting will apply.
3. Press the SET button. The flash power ratio is marked.
4. Use the arrow keys to set the desired correction value in steps of 1/3EV.
5. Confirm your setting with SET button.
Available flash power range: 1/1 (full power) to 1/128
GB INSTRUCTIONS FOR DÖRR DAF-320 TTL FLASH
• All flashes of group B will work with TTL mode and exposure correction of -0,3EV.
• All flashes of group C will work manually with ¼ power ratio
- Remote mode
- Master mode
- S1 Slave mode
- S2 Slave mode
CANON
5
Publicité
