Publicité
all the way down to be sure that the blade does not
contact any part of the lower base. Re-adjust slightly, if
necessary.
WARNING:
After installing a new blade and
with the battery cartridge removed, always be
sure that the blade does not contact any part of
the lower base when the handle is lowered com-
pletely. If a blade makes contact with the base, it may
cause kickback and result in serious personal injury.
► Fig.17
Sub-fence
Country specific
This tool is equipped with the sub-fence and small
sub-fences.
Sub-fence
WARNING:
Always remove sub-fence when
performing bevel cuts. Failure to do so may cause
serious injury.
► Fig.18: 1. Sub-fence
When performing cuts except for bevel cuts, use the
sub-fence to support the workpiece.
Small sub-fence
CAUTION:
When performing right bevel cuts,
fold the small sub-fences. Otherwise, they may
contact the blade or a part of the tool, and may result
in serious injury to the operator.
► Fig.19: 1. Small sub-fence 2. Scale
When performing vertical cut or left bevel cut, flip them
upward to support the workpiece. The guide fence has
a scale of 10 mm interval.
Adjusting the miter angle
► Fig.20: 1. Fixing screw 2. Turn base 3. Miter scale
4. Pointer
1.
Loosen the fixing screw counterclockwise.
2.
Adjust the angle of the turn base. Use the pointer
and the miter scale as a guide.
3.
Tighten the fixing screw clockwise firmly.
CAUTION:
After changing the miter angle,
always secure the turn base by tightening the
fixing screw firmly.
NOTICE:
When turning the turn base, be sure to
raise the handle fully.
Adjusting the bevel angle
To adjust the bevel angle, turn the lever at the rear of
the tool downward.
► Fig.21: 1. Lever
To tilt the blade to the left, hold the handle and tilt the
saw head. Use the bevel scale and the pointer as a
guide. Then turn the lever upward firmly to secure the
saw head.
► Fig.22: 1. Pointer 2. Bevel scale
To tilt the blade to the right, hold the handle and tilt the
saw head to the left slightly, and push the release but-
ton. With the release button pressed, tilt the saw blade
to the right. Turn the lever upward firmly to secure the
saw head.
► Fig.23: 1. Release button
CAUTION:
After changing the bevel angle,
always secure the saw head by turning the lever
upward firmly.
NOTICE:
When tilting the saw blade, be sure the
handle is fully raised.
NOTICE:
When changing bevel angles, be
sure to position the kerf boards appropriately
as explained in the "Positioning kerf boards"
section.
Setting 46° bevel angle
1.
Loosen the lever and tilt the blade to the left or
right fully.
► Fig.24: 1. Lever
2.
To tilt the blade to the left, hold the handle and tilt
the saw head to the right slightly, and then move the
release lever to the direction of the arrow. The bevel
angle can be adjusted between 45° to 46° by tilting the
saw head while moving the release lever.
To tilt the blade to the right, hold the handle and tilt the
saw head to the left slightly, and then move the release
lever to the direction of the arrow. The bevel angle can
be adjusted between 45° to 46° by tilting the saw head
while moving the release lever.
► Fig.25: 1. Lever 2. Release lever
3.
Turn the lever upward firmly to secure the saw
head.
Adjusting the lever position
If the lever does not provide full tightening in course of
time, change the position of the lever. The lever can be
repositioned at every 30° angle.
Loosen and remove the screw that secures the lever.
Remove the lever and install it again so that it points
slightly above the horizontal. Then, tighten the lever
with the screw firmly.
► Fig.26: 1. Lever 2. Screw
19 ENGLISH
Publicité
