Publicité
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may afect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
diferent from those intended could result in a hazardous
situation.
5) SERVICE
a) Have your power tool serviced by a qualiied repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR PLANERS
GENERAL
• This tool should not be used by people under the age
of 16 years
• The noise level when working can exceed 85 dB(A);
wear ear protection ④
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classiied as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
• SKIL can assure lawless functioning of the tool only
when original accessories are used
• Never use the tool when cord is damaged; have it
replaced by a qualiied person
• Always disconnect plug from power source before
making any adjustment or changing any accessory
BEFORE USE
• Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Before using the tool check that the knives do not brush
anywhere
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Use clamps or another practical way to secure and
support the workpiece to a stable platform (holding
the work by your hand or against the body leaves it
unstable and may lead to loss of control)
DURING USE
• Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord
(cutting a "live" wire may make exposed metal parts of
the power tool "live"and shock the operator)
• Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
• Keep your ingers away from the rotating knives
• In case of electrical or mechanical malfunction,
immediately switch of the tool and disconnect the plug
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• If any chip should get jammed in the chip outlet, you
should switch of the motor, ensure that all moving parts
have come to a complete standstill, disconnect the plug,
and remove the jammed chip
AFTER USE
• Wait for the cutter block to stop before setting the
tool down (an exposed knife may engage the surface
leading to possible loss of control and serious injury)
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut of the cord of
this tool, it must be disposed of safely and not left
unattended
USE
• Changing/reversing knives ⑥
This planer is equipped with non-grindable knives with
cutting edges on both sides; so if one side has become
blunt, the other side can be used
! switch of the tool and disconnect the plug
- remove guiding devices, if mounted
- take wrench from storage A
- turn tool upside down
- loosen 3 bolts B with wrench (do not remove bolts)
- push knife out of cutter block with piece of wood
- put knife back in cutter block in reversed position, or
use new knife
! groove in knife should match ledge in cutter
block
! both knife ends should protrude equally
- irmly tighten 3 bolts B with wrench
! change/reverse knives in time; only use sharp
knives
! always change/reverse both knives at the same
time
! do not attempt to adjust the knives with
cutter block screws C, which are pre-set at
manufacturing
• Adjusting planing depth ⑦
- turn knob D in "+"/"-" direction for increasing/
decreasing planing depth
- use indicator E as reference
- always select a shallow planing depth and repeat the
planing and adjusting process until the required depth
is reached
7
Publicité
