Publicité
GB
• The device must be standing clear all around on
an even, horizontal surface or be mounted
securely on the wall. The safety distances must
always be adhered to.
• The device may not be operated outdoors.
• The device may never be operated without super-
vision.
• Never put objects through the ventilation grate
into the device. Mortal danger!
• Never subject the device to water or other liquids.
• The device may neither be operated in rooms with
a bathtub, shower or swimming pool nor near
washbasins or water connections.
• The distance between the ventilation grate and
flammable objects must be at least 75 cm.
• The device may not be covered. There is danger
of fire.
• Do not use the heater in conjunction with a timer
or any other switch capable of automatic activa-
tion, as this creates a fire hazard.
• The heater must not be positioned beneath a wall
socket.
• Do not use adapters or extension cords.
• This appliance can be used by children aged from
8 years and above and by persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and if they understand
the hazards involved. Children shall not play with
the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
• Children of less than 3 years should be kept away
unless continuously supervised.
• Children aged from 3 years and less than 8 years
shall only switch on/off the appliance provided
that it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate and
clean the appliance or perform user maintenance.
• CAUTION! Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and vul-
nerable people are present.
• Symbols appearing on your device may not be
removed or covered. Signs on the device that are
no longer legible must be replaced immediately.
Read and observe the instructions for use
before using the product for the first time.
To prevent overheating, do not cover the heater!
Assembly
Note: The actual appearance of your prod-
uct may differ from the illustrations.
► Assembly – p. 3
24
Wall mounting
DANGER! Danger of electric shock!
Before drilling the holds, make sure that there
are no electrical or other lines in the wall.
DANGER! Risk of injury! The device may
not be mounted directly below a wall outlet.
Danger of cable fires!
Note: Please note that the product must be
installed at least 15 cm from the floor and 50
cm from the ceiling.
– The heater must be mounted at 4 points, ensure
there is a 300mm clearance on all sides of the heater.
► P. 3, item 1
– Measure the distance between the centre of each
bracket both horizontally and vertically to ensure
drilling holes in the correct place. Mark the positions
of the 4 holes to be drilled on the wall (2), use the
supplied wall mount drawings for correct measures.
– Drill the holes in the wall (3), then insert the plastic
expanded plugs (4) and screw the 4 supplied
screws into the plastic expanded plugs (5).
– Attached the panel heater onto the screws and
move the heater to the left so that the screws drop
into the securing slots (6).
Foot assembly
Note: If the heater is not mounted on the wall,
the supplied feet must be fitted to the unit.
► P. 4, item 7
– To fix the feet, remove the bottom screws from the
heater housing.
– Place the feet and secure them by putting the
screws back into the housing.
– Take care to ensure that the feet are located cor-
rectly on the button end of the heater.
Operation
Check before switching on!
DANGER! Risk of injury! The device must
only be put into operation if no faults are found
during the check-up. If any part of the device is
defective, it must be replaced before the next use.
Check the safe condition of the device:
– Check whether there are any visible defects.
– Check whether all parts of the device are firmly
attached.
Operating instructions
To begin to use the heater, please follow these instructions:
1. Connect to the power supply, turn on the product
master switch, press the ON/OFF button, then
press the WIFI button for 6 second, the WIFI icon
flashes, observe the WIFI icon flashing speed
state (fast flash 3-1 second, slow flash 1-3 sec-
onds), heater in heating state (default heating tem-
perature 37°C, if the ambient temperature is lower
than 37°C, the heater will be in the heating state)
2. Power button: Touch the "power button", the LCD
will light up. The middle temperature of the LCD
screen shows the ambient temperature. When
the ambient temperature is lower than the default
Publicité
