Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 9
TFA_No. 35.1094 Anleitung_01_15
ACCENT – Wireless weather station
Notes:
The time base for the radio controlled time is a Caesium Atomic Clock operated by the
Physikalisch Technische Bundesanstalt Braunschweig which has a time deviation of less
than one second in one million years. The time is coded and transmitted from Main-
flingen near Frankfurt via frequency signal DCF-77 (77.5 kHz) and has a transmitting
range of approximately 1500 km. Your radio-controlled clock receives this signal and
converts it to show the precise time in summer or wintertime. "S" appears on the
display during summer time. The quality of the reception depends greatly on the
geographic location. In normal cases, there should be no reception problems within a
1500 km radius around Frankfurt.
Please take note of the following:
• Recommended distance to any interfering sources like computer monitors or TV
sets is a minimum of 1.5 - 2 metres.
• Within ferro-concrete rooms (basements, superstructures), the received signal is
naturally weakened. In extreme cases, please place the unit close to a window
and/or point its front or back towards the Frankfurt transmitter.
• During night-time midnight until appr. 4.00 h in the morning), the atmospheric
disturbances are usually less severe and reception is possible in most cases. A single
weekly reception is adequate to keep the accuracy deviation below 1 second.
4. How to operate
4.1 Manual setting of clock and calendar
• Hold MODE button in normal mode. The day-of-week language digit is flashing.
Press ▲ or ▼ button to adjust it. Day-of-week language: German (GE), French (FR),
Italian (IT), Spanish (SP), Dutch (NE), Swedish (SW) and English (EN).
• Press MODE button and the setting sequence is shown as follows: Years, month,
date, month/day or day/month sequence, 12 and 24 hours system indication, hours
and minutes. Press ▲ or ▼ button to make the desired settings
• Display of date day/month (DM) or month/day (MD): Press ▲ or ▼ button to select
between month/date (M/D, American version) or date/month (D/M, European
version).
• In 12 HR system PM appears after 12 h on the display.
• Confirm with MODE button.
• Holding ▲ or ▼ button, you will enter fast mode.
• The instrument will quit automatically the setting mode, if there is no button used
within 60 seconds.
4.2 Dual time
• Press MODE button two times in normal mode.
• ZONE appears on the display.
• Hold MODE button.
• 0:00+ flashes on the display. Press ▲ or ▼ button to adjust the time zone in 30 min.
steps (+15/-13) for the dual time.
• Holding ▲ or ▼ button, you will enter fast mode.
• Confirm with MODE button.
12
02.02.2015
10:07 Uhr
Seite 7
ACCENT – Wireless weather station
4.3 Indication of time
• Each press on the MODE button in normal mode will change the display between:
Time with seconds
Time with day-of-week
Dual time with day of week
Dual time with seconds

4.4 Alarm setting

• Press ALARM button.
• OFF or the last adjusted alarm time and W appears on the display.
• You can now adjust the alarm time for the weekdays (Monday until Friday).
• Press and hold ALARM button.
• The hour digit is flashing. Press ▲ or ▼ button to adjust hours.
• Press ALARM button again and set minutes in the same way.
• Holding ▲ or ▼ button, you will enter fast mode.
• Confirm with ALARM button.
• Alarm time and W appears on the display. The alarm is activated.
• Press ALARM button again
• OFF or the last adjusted alarm time and S appears on the display.
• You can adjust the alarm time for the weekend (Saturday and Sunday) or a special
alarm time in the same way.
• Confirm with ALARM button.
• Alarm time and S appears on the display. The alarm is activated.
• Press ALARM button again
• S and W appears on the display. Both alarm times are activated.
• Once the alarm starts to ring (3 different sounds), W or S flashes.
• Press ALARM button to stop the alarm.
• The alarm stays active from Monday until Friday.
• Please consider that you have to activate the weekend or special alarm time always
new.
• To activate/turn off (OFF) the alarm function, press ▲ or ▼ button in the desired
alarm mode.
5. °C/°F function
• Press °C/°F button to change between °C (Celsius) or °F (Fahrenheit) as temperature
unit.
6. Max./Min. memory
• Press MEM button in normal mode and the lowest outdoor and indoor tempera-
ture is displayed since the last reset.
• MIN appears on the display.
• Press MEM button in normal mode again and the highest outdoor and indoor tem-
perature is displayed since the last reset.
• MAX appears on the display.
• Press MEM button again and you will return to normal mode.
• Hold MEM button in the desired mode to clear the recorded MAX/MIN reading
(5 sec.).
13

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

35.1094

Table des Matières