Publicité
Liens rapides
Item:
LWRAPA2-25PCS
LWRAPA4-50PCS
LWRAPA2-25PCS-EM
LWRAPA4-50PCS-EM
LWRAPA-OS-PIR-BT
INSTALLATION INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
Make all electrical and ground connections in accordance with local codes or the National
Electrical Code. If you are not familiar with these codes and requirements, consult a
qualified electrician. This Professional should be familiar with the construction and
operation of this product and hazards involved. Failure to do so may result in serious
personal injury.
To reduce the risk of fire, electric shock, personal injury, or property damage, please read
and follow all safety instructions. If you do not understand these instructions or if any
additional information is required, contact your local Topaz representative. Retain these
instructions for maintenance reference.
Do not exceed the allowed supply voltage marked on the luminaire label information.
Disconnect power at the circuit breaker panel before any installation.
Do not expose wire to any sharp objects such as sheet metal to prevent wiring damage or
abrasion.
While the light is on, please avoid direct eye exposure.
Combustible material should be kept away from fixture/LENS.
Do not make or alter any open holes in any enclosure or any electrical component during
installation.
Do not use when the enclosure is damaged or broken in any way.
Do not alter, relocate or remove wiring, lamp holder power supply or any other electrical
component.
Pursuant to NEC 410.69, "Effective January 1, 2022, where control conductors are spliced,
terminated, or connected in the same luminaire or enclosure as the branch-circuit
conductors, the field-connected control conductor shall not be of a color reserved for the
grounded branch circuit conductor or the equipment grounding conductor." And NEC
200.6(A)(2), "An insulated grounded conductor of 6 AWG or smaller shall be identified by
one of the following means: (2) The insulated conductor shall have a continuous gray outer
finish." For this reason, Topaz® will be transitioning from using Purple and Gray dimming
wires, to Purple and Pink dimming wires.
Included Hardware:
Large Philips
Wall Anchors (4)
Head Screws (4)
©2023 Southwire Company, LLC. All rights reserved.*Registered Trademark & Trademark of Southwire Company, LLC.
ARCHITECTURAL WRAP
WARNING
CAUTION
Wire Nuts (3)
800-666-2852 | SOUTHWIRE.COM
Publicité
Manuels Connexes pour Topaz LWRAPA2-25PCS
Sommaire des Matières pour Topaz LWRAPA2-25PCS
- Page 1 200.6(A)(2), “An insulated grounded conductor of 6 AWG or smaller shall be identified by one of the following means: (2) The insulated conductor shall have a continuous gray outer finish.” For this reason, Topaz® will be transitioning from using Purple and Gray dimming wires, to Purple and Pink dimming wires.
- Page 2 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT ARCHITECTURAL WRAP INSTALLATION INSTRUCTIONS Pre-Installation Instructions: 1. Before installing or servicing any part of this fixture, turn off AC power at the circuit breaker. 2. Remove diffuser by rolling it off of the edge lip all the way down 1 side.
- Page 3 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT ARCHITECTURAL WRAP INSTALLATION INSTRUCTIONS Junction Box Mounting Instructions: 1. Adjust the 2 screws from the junction box to stick out about 1/4” to mount the fixture base in later steps. See Figure 4. Junction Box Screws...
- Page 4 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT ARCHITECTURAL WRAP INSTALLATION INSTRUCTIONS DRYWALL MOUNTING 3. Place the fixture aside. If the mounting holes go through drywall without a stud, drill a pilot hole in each of the markings using a 1/8” drill bit.
- Page 5 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT ARCHITECTURAL WRAP INSTALLATION INSTRUCTIONS V-Hook and Chain Mounting Instructions: 1. Install mounting hooks (Not Included) spaced according to See Chart the chart below. 2. Place the link that gives you the desired mounting height on the hook and thread the V-Hook through the last link in the chain as shown in Figure 11.
- Page 6 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT ARCHITECTURAL WRAP INSTALLATION INSTRUCTIONS Align the sensor endcap with the fixture endcap and pass the wires from the sensor endcap into the fixture. See Figure 14. Figure 14 Secure the sensor endcap to the fixture using the supplied screws.
- Page 7 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT ARCHITECTURAL WRAP INSTALLATION INSTRUCTIONS Wiring Diagram: • Make the wire connections Black to Line, White to Neutral and Green to Ground. Use the supplied BLACK (LINE) ToSource wire nuts to secure the connections. See Figure...
- Page 8 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT ARCHITECTURAL WRAP INSTALLATION INSTRUCTIONS Final Installation Instructions: 1. Swing the LED panel closed and fasten in place with the 2 screws removed during Pre-installation. See Figure 20. Figure 20 2. Install the diffuser starting at one end of fixture base, insert diffuser slot onto edge of luminaire housing.
- Page 9 être identifié par l’un des moyens suivants: (2) Le conducteur isolé doit avoir une finition extérieure grise continue. » Pour cette raison, Topaz® passera de l’utilisation de fils de gradation violets et gris aux fils de gradation violets et roses.
- Page 10 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT LUMINAIRE ARCHITECTURAL INSTRUCTIONS D’INSTALLATION Précédant l’Installation : 1. Avant d’installer ou de réparer toute partie de ce luminaire, coupez l’alimentation en c.a. au niveau du disjoncteur. 2. Retirez le diffuseur en le dégageant du rebord et en le faisant basculer d’un côté.
- Page 11 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT LUMINAIRE ARCHITECTURAL INSTRUCTIONS D’INSTALLATION Instructions de Montage Sur la Boîte de Junction: 1. Ajustez les 2 vis de la boîte de jonction pour sortir environ 6,35 mm pour monter la base du luminaire dans les étapes Vis de boîte de jonction...
- Page 12 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT LUMINAIRE ARCHITECTURAL INSTRUCTIONS D’INSTALLATION MONTAGE SUR CLOISON SÈCHE 3. Mettez le luminaire de côté. Si les trous de montage traversent une cloison sèche sans rencontrer de montant mural, percez un avant-trou à chaque marque à l’aide d’une mèche de 1/8 po (3,2 mm).
- Page 13 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT LUMINAIRE ARCHITECTURAL INSTRUCTIONS D’INSTALLATION Instructions de Montage de V-Hook et de chaîne: 1. Installez des crochets de montage (non inclus) espacés de Voir le tableau 1030,25mm. 2. Placez le maillon qui vous donne la hauteur de montage souhaitée sur le crochet et enfilez le V-Hook à...
- Page 14 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT LUMINAIRE ARCHITECTURAL INSTRUCTIONS D’INSTALLATION Alignez l’embout du détecteur avec l’extrémité du luminaire et faites passer les fils de l’embout du détecteur dans le luminaire. Reportez-vous à la figure 14. Figure 14 Fixez l’embout du détecteur au luminaire à l’aide des vis fournies.
- Page 15 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT LUMINAIRE ARCHITECTURAL INSTALLATION INSTRUCTIONS Schéma de Câblage: • Raccordez le fil noir au fil de phase, le fil blanc au fil ToSource NOIR (LINE) neutre et le fil vert à la mise à la terre. Utilisez les...
- Page 16 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT LUMINAIRE ARCHITECTURAL INSTRUCTIONS D’INSTALLATION Instructions d’installation finales : 6. Refermez le panneau de DEL et fixez-le en place à l’aide des deux vis retirées à l’étape précédant l’installation. Reportez- vous à la figure 20.
- Page 17 6 AWG o menor se identificará por uno de los siguientes medios: (2) El conductor aislado tendrá un acabado exterior gris continuo". Por esta razón, Topaz® pasará de usar cables de atenuación púrpura y gris a cables de atenuación púrpura y rosa.
- Page 18 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT MARCO ARQUITECTÓNICO INSTRUCCIONES DE INSTALACIÓN Instrucciones Previas a la Instalación: 1. Antes de instalar o reparar cualquier parte de esta lámpara, desconecta la alimentación de CA en el disyuntor. 2. Retira el difusor girándolo desde el extremo del borde hacia abajo por un lado.
- Page 19 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT MARCO ARQUITECTÓNICO INSTRUCCIONES DE INSTALACIÓN Instrucciones de Montaje en la Caja de Conexiones: 1. Ajuste los 2 tornillos de la caja de conexiones para que sobresalgan aproximadamente 6 mm(1/4“) para montar la Tornillos de caja de conexiones base del accesorio en pasos posteriores.
- Page 20 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT MARCO ARQUITECTÓNICO INSTRUCCIONES DE INSTALACIÓN MONTAJE EN PANEL DE YESO 3. Coloca la lámpara a un lado. Si los orificios de montaje atraviesan paneles de yeso sin vigas, taladra un orificio guía en cada una de las marcas con una broca de 1/8".
- Page 21 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT MARCO ARQUITECTÓNICO INSTRUCCIONES DE INSTALACIÓN Instrucciones de Montaje de vancho y cadena: 1. Instale ganchos de montaje (no incluidos) espaciados a 40- Ver la Tabla 9/16" de distancia. 2. Coloque el eslabón que le proporcione la altura de montaje deseada en el gancho y enrosque el gancho en V a través...
- Page 22 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT MARCO ARQUITECTÓNICO INSTRUCCIONES DE INSTALACIÓN Alinea la tapa del extremo del sensor con la tapa del extremo del equipo y pasa los cables desde la tapa del extremo del sensor al equipo. Ver Figura 14.
- Page 23 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT MARCO ARQUITECTÓNICO INSTALLATION INSTRUCTIONS Diagrama de Cableado: • Haz las conexiones de los cables Negro a Línea, ToSource NEGRO (LINE) Blanco a Neutro y Verde a Tierra. Utiliza las tuercas BLANCO (NEUTRAL) ADORNO 120-277V...
- Page 24 Item: LWRAPA2-25PCS LWRAPA4-50PCS LWRAPA2-25PCS-EM LWRAPA4-50PCS-EM LWRAPA-OS-PIR-BT MARCO ARQUITECTÓNICO INSTRUCCIONES DE INSTALACIÓN Instrucciones finales de instalación: 6. Gira el panel LED para cerrarlo y fíjalo en su lugar con los 2 tornillos retirados durante la preinstalación. Ver Figura 20. Figura 20 7.