Publicité
Liens rapides
Item:
LWRAPU4-40-40K-D
LWRAPU2-20-40K-D
INSTALLATION INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
Make all electrical and ground connections in accordance with local codes or the National
Electrical Code. If you are not familiar with these codes and requirements, consult a
qualified electrician. This Professional should be familiar with the construction and
operation of this product and hazards involved. Failure to do so may result in serious
personal injury.
To reduce the risk of fire, electric shock, personal injury, or property damage, please read
and follow all safety instructions. If you do not understand these instructions or if any
additional information is required, contact your local Topaz representative. Retain these
instructions for maintenance reference.
Do not exceed the allowed supply voltage marked on the luminaire label information.
Disconnect power at the circuit breaker panel before any installation.
Do not expose wire to any sharp objects such as sheet metal to prevent wiring damage or
abrasion.
While the light is on, please avoid direct eye exposure.
Combustible material should be kept away from fixture/LENS.
Do not make or alter any open holes in any enclosure or any electrical component during
installation.
Do not use when the enclosure is damaged or broken in any way.
Do not alter, relocate or remove wiring, lamp holder power supply or any other electrical
component.
Pursuant to NEC 410.69, "Effective January 1, 2022, where control conductors are spliced,
terminated, or connected in the same luminaire or enclosure as the branch-circuit
conductors, the field-connected control conductor shall not be of a color reserved for the
grounded branch circuit conductor or the equipment grounding conductor." And NEC
200.6(A)(2), "An insulated grounded conductor of 6 AWG or smaller shall be identified by
one of the following means: (2) The insulated conductor shall have a continuous gray outer
finish." For this reason, Topaz® will be transitioning from using Purple and Gray dimming
wires, to Purple and Pink dimming wires.
Included Hardware:
Large Philips
Small Philips Head
Screws (2)
Head Wood
Screws (4)
www.topaz-usa.com | 800.666.2852 | ©2022 Southwire Company, LLC. All rights reserved.
LWRAPU4-40-50K-D
LWRAPU2-20-50K-D
LED UTILITY WRAP
WARNING
CAUTION
Wall Anchors (4)
Wire Nuts (3)
Publicité
Manuels Connexes pour Topaz LWRAPU4-40-40K-D
Sommaire des Matières pour Topaz LWRAPU4-40-40K-D
- Page 1 200.6(A)(2), “An insulated grounded conductor of 6 AWG or smaller shall be identified by one of the following means: (2) The insulated conductor shall have a continuous gray outer finish.” For this reason, Topaz® will be transitioning from using Purple and Gray dimming wires, to Purple and Pink dimming wires.
- Page 2 être identifié par l’un des moyens suivants: (2) Le conducteur isolé doit avoir une finition extérieure grise continue. » Pour cette raison, Topaz® passera de l’utilisation de fils de gradation violets et gris à des fils de gradation violets et roses.
- Page 3 Y NEC 200.6 (A) (2), "Un conductor aislado a tierra de 6 AWG o menor se identificará por uno de los siguientes medios: (2) El conductor aislado tendrá un acabado exterior gris continuo". Por esta razón, Topaz® pasará de usar cables de atenuación púrpura y gris a cables de atenuación púrpura y rosa.
- Page 4 Asegúrate de dejar fuera los tornillos alrededor de 6 mm (1/4”) para montar la base de la lámpara en pasos posteriores. Ver la Figura 2. www.topaz-usa.com | 800.666.2852 | ©2022 Southwire Company, LLC. All rights reserved.
- Page 5 Figure 4 blanco y verde. Conecta el morado y el rosa a un regulador de intensidad compatible de 0-10 V. www.topaz-usa.com | 800.666.2852 | ©2022 Southwire Company, LLC. All rights reserved.
- Page 6 (Parte C) de la base de la lámpara (Parte A). Desliza el difusor (Parte B) en la tapa del extremo estacionario y permite que la tapa del extremo con bisagras se cierre en la lámpara. 7. Conecta la corriente alterna. www.topaz-usa.com | 800.666.2852 | ©2022 Southwire Company, LLC. All rights reserved.
- Page 7 Asegúrate de no apretar los tornillos completamente hasta abajo. Deja fuera la cabeza de cada tornillo aproximadamente 6 mm (1/4”). Salta al Paso 6. www.topaz-usa.com | 800.666.2852 | ©2022 Southwire Company, LLC. All rights reserved.
- Page 8 ADVERTENCIA: Asegúrate de que los anclajes sean aceptables para la superficie de montaje y puedan soportar el peso de la lámpara. Es posible que se requieran otros anclajes de pared (no incluidos). www.topaz-usa.com | 800.666.2852 | ©2022 Southwire Company, LLC. All rights reserved.
- Page 9 Figure 9 rosa a través del orificio junto con los cables negro, blanco y verde. Conecta el morado y el rosa a un regulador de intensidad compatible de 0-10 V. www.topaz-usa.com | 800.666.2852 | ©2022 Southwire Company, LLC. All rights reserved.
- Page 10 (Parte C) de la base de la lámpara (Parte A). Desliza el difusor (Parte B) en la tapa del extremo estacionario y permite que la tapa del extremo con bisagras se cierre en la lámpara. 10. Conecta la corriente alterna. www.topaz-usa.com | 800.666.2852 | ©2022 Southwire Company, LLC. All rights reserved.
- Page 11 **REMARQUE : CES INSTRUCTIONS NE TRAITENT PAS DE TOUTES LES PERMUTATIONS QUI PEUVENT EXISTER DANS L’INSTALLATION, LA MAINTENANCE ET L’ENVIRONNEMENT D’EXPLOITATION. ** NOTA: ESTAS INSTRUCCIONES NO ABORDAN TODAS LAS PERMUTACIONES QUE PUEDEN EXISTIR EN EL ENTORNO DE INSTALACIÓN, MANTENIMIENTO Y FUNCIONAMIENTO. www.topaz-usa.com | 800.666.2852 | ©2022 Southwire Company, LLC. All rights reserved.