Publicité
14 | English
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑11.
Typically, the A-weighted sound pressure level of the power
tool is 75 dB(A). Uncertainty K = 5 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑11:
Cutting boards with saw blade NanoBlade Wood Speed 65:
2
2
a
< 2.5 m/s
, K = 1.5 m/s
.
h,B
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Battery Charging (see figure B)
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Selecting the saw blade
Only use saw blades that are suitable for the material you are going to cut. The saw blade should not be longer than required
for the cut you want to make.
Saw blade
NanoBlade Wood Basic
NanoBlade Wood Speed
NanoBlade Wood Speed
1 609 92A 87S | (04.08.2022)
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
To remove the battery (5), press the release button (6) and
pull the battery back and out of the power tool. Do not use
force to do this.
Battery charge-control indicator
When the on/off switch (4) is pressed in halfway or com-
pletely, the battery charge indicator (8) indicates the bat-
tery's state of charge for a few seconds. It consists of an LED
which lights up in two colours.
LED
Lit green
Lit red
Flashing red
A) The battery charge indicator will also flash red if the battery has
overheated or overloaded.
Inserting/changing the saw blade
When fitting or changing the saw blade, wear protect-
u
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
Take care not to hold the power tool close to the on/
u
off switch or by the on/off switch and lock-off button
when changing the saw blade. There is risk of injury
from unintentionally pressing the on/off switch.
Avoid contact with the skin when changing a saw
u
blade and use protective gloves in perfect condition.
The saw blade can become hot when in operation for a
long time.
Do not pull on the chain and do not pull the chain off
u
the guide unit.
Always replace a complete saw blade with another complete
saw blade. The chain cannot be replaced on its own.
Cutting depth
Order number
50 mm
2 609 256 D83
50 mm
2 609 256 D84
65 mm
2 609 256 D86
Capacity
≥ 30%
< 30%
A)
0%
Materials
Wood, plastic (PVC, PC, PMMA)
Wood, plastic (PVC, PC, PMMA)
Wood, plastic (PVC, PC, PMMA)
Bosch Power Tools
Publicité
