Publicité
Ensure that the footplate always rests securely while
u
sawing. A jammed saw blade can break or lead to kick-
back.
When the cut is completed, switch off the power tool
u
and then pull the saw blade out of the cut only after it
has come to a standstill. In this manner you can avoid
kickback and can place down the power tool securely.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Use only undamaged saw blades that are in perfect
u
condition. Bent or dull saw blades can break, negatively
influence the cut, or lead to kickback.
Do not brake the saw blade to a stop by applying side
u
pressure after switching off. The saw blade can be dam-
aged, break or cause kickback.
Only use the power tool with the base plate. If you do
u
not use the base plate, you are at risk of not being able to
control the power tool.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Make sure you have firm footing when operating the
u
power tool, especially when using it standing on steps
or ladders. Slippery or unstable surfaces can cause you
to lose your balance or lose control over the power tool.
The chain of the saw blade can tear if subjected to ex-
u
cessive strain. You should replace the power tool and/
or saw blade if this happens.
Bosch Power Tools
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for domestic use only. It is inten-
ded for cutting branches, slats, hardwood and softwood. It is
suitable for straight cuts.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Saw blade
(2) Base plate
(3) Lock-off button for on/off switch
(4) On/off switch
(5) Battery
(6) Battery release button
(7) Suspension strap
(8) Battery charge indicator
(9) Cover of the saw blade receptacle
(10) Locking lever of the saw blade receptacle cover
(11) Handle (insulated gripping surface)
(12) Saw blade receptacle
Technical Data
All-purpose saw
Article number
Rated voltage
Max. cutting depth
Weight according to
EPTA‑Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation
and
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
English | 13
EasyCut 12
3 603 CC9 0..
V=
12
mm
65
A)
kg
0.90
°C
0 to +35
°C
–20 to +50
PBA 12V...
GAL 12...
1 609 92A 87S | (04.08.2022)
Publicité
