Publicité
TECHNICAL DATA
Type
Production code
Battery voltage
No-load speed
Torque max.
Tool reception
Weight without battery
Weight according EPTA-Procedure 01/2014 (2,0 Ah)
Recommended ambient operating temperature
Recommended battery types
Recommended charger
Noise Information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Wear ear protectors.
Vibration Information
Total vibration values (vector sum in the three axes) determined
according to EN 62841.
Vibration emission value a
/ Uncertainty K
h
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test
given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING
Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT DRIVER SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing loss.
Hold the power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the
operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety
shoes, hard hat or hearing protection used for appropriate
conditions will reduce personal injuries.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Do not machine any materials that present a danger to health
(e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive
force. Determine why the insertion tool stalled and rectify this,
paying heed to the safety instructions.
The possible causes may be:
14
M12 FHIR14LR
M12 FHIR38LR
Cordless industrial screwdriver Cordless industrial screwdriver
4815 40 01 XXXXXX MJJJJ
4815 47 01 XXXXXX MJJJJ
12 V
12 V
0–450 min
-1
0–450 min
47,5 Nm
47,5 Nm
1/4" (6,35 mm)
3/8" (9,5 mm)
0,88 kg
0,91 kg
1,06 kg
1,10 kg
-18...+50 °C
M12B...
M12-18C, M12-18AC, M12-18FC, C12C
84,63 dB(A) / 3 dB(A)
85,93 dB(A) / 3 dB(A)
95,63 dB(A) / 3 dB(A)
96,63 dB(A) / 3 dB(A)
2,52 m/s
2
/ 1,5m/s
2
2,80 m/s
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool is sharp-edged and can become hot during
use.
WARNING! Danger of cuts and burns
- when handling the insertion tools
- when setting the device down.
Wear protective gloves when handling insertion tools.
Chips and splinters must not be removed while the machine is
running.
When working in walls ceiling, or fl oor, take care to avoid electric
cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse
or by burning them. Milwaukee Distributors off er to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System M12 chargers for charging System M12 battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and immediately
ENGLISH
seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fl uid or allow a fl uid to fl ow inside them.
Corrosive or conductive fl uids, such as seawater, certain
-1
industrial chemicals, and bleach or bleach containing products,
etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The cordless industrial screwdriver can be used to tighten and
loosen nuts and bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal
use.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise in use and the operator should pay special
attention to avoid the following:
• Injury caused by vibration.
Hold the product by designated handles and restrict working
time and exposure.
2
/ 1,5m/s
2
• Exposure to noise can cause hearing injury.
Wear ear protection and limit exposure.
• Injury due to fl ying debris
Wear eye protection, heavy long trousers and substancial
footwear at all times.
• Inhalation of toxic dusts.
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Batteries which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and batteries must be kept clean.
For an optimum life-time, the batteries have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery
from the charger once it is fully charged.
For battery storage longer than 30 days:
Store the battery where the temperature is below 27°C and away
from moisture
Store the battery in a 30% - 50% charged condition
Every six months of storage, charge the battery as normal.
Battery protection for Li-Ion Akkus
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate for
about 5 seconds, the fuel gauge will fl ash,and then the tool will
turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the
battery pack could raise too much. If this happens, the fuel
gauge will fl ash until the battery pack cooled down. After the
lights go off , the work may continue.
Transport of Lithium Batteries
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insula-
ted to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
CLEANING
The ventilation slots of the machine must be kept clear at all
times.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Do not dispose of waste batteries, waste
electrical and electronic equipment as unsorted
municipal waste. Waste batteries and waste
electrical and electronic equipment must be
collected separately.
Waste batteries, waste accumulators and light
sources have to be removed from equipment.
Check with your local authority or retailer for
recycling advice and collection point.
According to local regulations retailers may have
an obligation to take back waste batteries and
Waste electrical and electronic equipment free
of charge.
Your contribution to re-use and recycling of waste
batteries and waste electrical and electronic
equipment helps to reduce the demand of raw
materials.
Waste batteries, in particular containing lithium
and waste Electrical and electronic equipment
contain valuable, recyclable materials, which can
adversely impact the environment and the human
health, if not disposed of in an environmentally
compatible manner.
Delete personal data from waste equipment, if
any.
n
No-load speed
0
V
Voltage
Direct Current
ENGLISH
15
Publicité
