Publicité
MAINTENANCE AND CLEANING
WARNING
!
•
Do not use steam cleaning equipment.
Before cleaning, make sure the cooking zones are switched o and that the residual heat indicator ("H") is not displayed.
•
Important:
•
Do not use abrasive sponges or scouring pads as they may damage
the glass.
•
After each use, clean the hob (when it is cool) to remove any deposits
and stains from food residue.
•
A surface that is not kept suitably clean may reduce the sensitivity of
control panel buttons.
•
Use a scraper only if residues are stuck to the hob. Follow the scraper
manufacturer's instructions to avoid scratching the glass.
•
Sugar or foods with high sugar content can damage the hob and
must be immediately removed.
•
Salt, sugar and sand could scratch the glass surface.
•
Use a soft cloth, absorbent kitchen paper or a special hob cleaner (follow
the Manufacturer's instructions).
•
Spills of liquid in the cooking zones can cause the pots to move or vibrate.
•
After cleaning the hob, dry thoroughly.
TROUBLESHOOTING
•
Check that the electricity supply has not been shut o .
•
If you cannot turn the hob o after using it, disconnect it from the power
supply.
•
If alphanumeric codes appear on the display when the hob is switched on,
consult the following table for instructions.
DISPLAY CODE
Cookware is detected but it is not
compatible with requested operation.
F0E1
Wrong power cord connection.
F0E7
The control panel switches o because
F0EA
of excessively high temperatures.
The cooking zone turns o when the
F0E9
temperatures are too high.
F0E2, F0E4, F0E6,
Disconnect the hob from the power supply.
F0E8, F0EC, F1E1,
Wait a few seconds then reconnect the hob to the power supply.
F2E1, F6E1, F6E3,
If the problem persists, call the service centre and specify the error code that appears on the display.
F7E5, F7E6
d E
The hob does not switch heat up.
[when the hob is off]
The functions do not come on.
The hob does not allow a special
function to be activated.
e.g.
:
The hob automatically sets a minimum
e.g.
power level to ensure that the cooking
[Power level lower than
zone can be used.
level requested]
DESCRIPTION
The cookware is not well positioned on
the cooking zone, or it is not compatible
with one or more cooking zones.
The power supply connection is not
exactly as indicated in "ELECTRICAL
CONNECTION" paragraph.
The internal temperature of electronic
parts is too high.
The internal temperature of electronic
parts is too high.
DEMO MODE on.
The power regulator limits the power
levels in accordance with the maximum
value set for the hob.
The power regulator limits the power
levels in accordance with the maximum
value set for the hob.
If the CleanProtect logo is present on the glass, the hob has been treated
with CleanProtect technology. This exclusive coating ensures excellent
cleaning results and keeps the hob surface shiny for longer.
Daily cleaning after each use is suggested.
To clean CleanProtect hobs, follow these recommendations:
•
Soak the zones that need to be cleaned with water making sure to
cover the entire stained area and being careful not to drop water on
the control panel.
•
For the water soaking:
•
In normal conditions, wait at least 2 minutes.
•
In heavy-dirt conditions, wait for at least 5 minutes.
•
If the water dries on the hob it is necessary to repeat the soaking step.
•
Use a non-abrasive sponge to remove deposits and dry the hob after
cleaning.
Please note: The presence of water, liquid spilled from pots or any objects
resting on any of the hob buttons can accidentally activate or deactivate
the control panel lock function.
POSSIBLE CAUSES
SOLUTION
Press On/O
button twice to remove the
F0E1 code and restore the functionality of the
cooking zone. Then, try to use the cookware
with a di erent cooking zone, or use di erent
cookware.
Adjust
the
power
supply
according to "ELECTRICAL CONNECTION"
paragraph.
Wait for the hob to cool down before using it
again.
Wait until the cooking area has cooled o
before using it again.
Follow the instructions in the "DEMO MODE"
paragraph.
See paragraph "Power management".
See paragraph "Power management".
EN
connection
Publicité
