Publicité
• "Pulse" function: Turn the control knob (E) to the "Pulse" position. Using
a succession of pulses gives finer control for precise preparations. In
this position, the appliance starts directly on maximum speed. It stops
as soon as you release the knob. The light remains on when the pulse
function is in use.
• Function "
Smoothie"
This function is used to prepare smoothies, milkshakes and fruit
cocktails. The speed is pre-programmed for best results. To use this
function, press the "Smoothie" button (B). The light remains on during
this cycle and switches off when the cycle is finished. The program stops
automatically. You can stop it before the end by positioning the control
button (E) on 0.
• Function "
Ice crush"
You can use this function to crush ice finely with pre-programmed operating
cycles and speed. To use this function, press the "Ice crush" button (C).
The light remains on during this cycle and switches off when the cycle is
finished. The program stops automatically but you can stop it before the
end by positioning the control button (E) on 0.
• Function "Auto clean":
This function is used to automatically clean your appliance. Press the
"Auto clean" button (D). Do not exceed 1 litre of hot water (maximum
temperature of 80°C / 176°F). At the end of the program, the appliance
stops automatically and you hear 4 beeps.
• WARNING : If the load becomes too high, your appliance will stop
automatically for safety reasons (if the motor runs for more than
3 minutes or if you have used too much ingredients). To restart your
appliance, turn the control knob to
and can be up to 30 minutes. Before restarting your appliance, adapt
the quantity of ingredients or blending time to avoid any overload.
You can then select the desired speed or function to complete your
preparation.
• WARNING : Do not use the program functions smoothie, ice crush
and auto clean with the herb chopper (K) and spice grinder (L).
These programs can only be used with the blender jug (F). Do not
perform ice crush with the herb chopper (K) and spice grinder (L).
48
. The overall cooling time may vary
USING THE HERB CHOPPER (K) AND SPICE GRINDER (L)
(DEPENDING ON MODEL)
– With the herb chopper (K) you can chop ingredients like onions, garlic
or raw meat (pre-cut into small pieces) in a few seconds. Do not use
the herb chopper for liquid preparations (fruit juices, etc.).
– With the spice grinder (L) you can grind spices in a few seconds:
coriander seeds, peppercorns, etc.
– These accessories are equipped with a bowl (M) that prevents access
to the blades during use.
1. Turn the bowl (M) upside down and add the ingredients.
2. Position the seal (K1 or L1) in its recess on the blade unit (K2 or L2)
(Fig. 13). Position the blade unit on the bowl. Lock the accessory by
rotating the blade unit until fully assembled (Fig. 14). Caution: leaks
can occur if the accessory is not locked correctly.
3. Rotate the assembled accessory (K or L) and position it on the
motor unit (Fig. 15).
4. Then turn the assembled accessory (K or L) through a quarter turn
clockwise (Fig. 15).
5. Plug in the appliance and turn the Control knob (E) to the desired
position or apply a few pulses. To stop the appliance, turn the
control knob (E) to position zero.
6. Unlock the accessory by turning it through a quarter turn in the
anticlockwise direction. Remove the assembled accessory (K+M or
L+M) from the motor unit. Turn it over before opening to avoid any
spillage of your preparation. Then you can unlock the blade unit
(K1 or L1). The blades are very sharp: handle them with caution
to avoid injury. You can then remove the preparation in the bowl.
Warning : Do not use the accessories for chopping or grinding liquid
or grains too hard (ex: hard black beans, sugar ...). You can pour liquid
ingredients in the blender jug (F) only.
ADVICE
• Depending on the nature of the ingredients, you can use the blender
jug to prepare up to
* 1.5 L for thick mixtures.
* 1.25 L for liquid preparations.
EN
49
Publicité
