Publicité
RP 210 Press Tool
Pressing at temperatures down to 0°F (-20°C) can be
done by warming the 1.1Ah battery above 15°F (-10°C) or
using a larger capacity battery (2.2Ah or 3.3Ah).
The red and green LED's on the tool will glow when the
tool temperature is between 0°F (-20°C) and 15°F (-10°C).
If using a 1.1Ah battery, the tool may not be able to
press the connection completely. If this occurs, the tool will
stop in the middle of the press cycle and will not release
from the connection. To remove the tool from the con-
nection, press the pressure release button on the right
hand side of the tool (shown in Figure 11) . This con-
nection then must be repressed while using either a
1.1Ah battery above 15°F (-10°C) or using a 2.2Ah
or 3.3Ah battery to insure a complete connection.
To use the press tool between 0°F (-20°C) and 15°F
(-10°C) either:
• Use a 2.2Ah or 3.3Ah battery
• Or maintain the 1.1Ah battery temperature above
15°F (-10°C). This can be done by placing the bat-
tery in an interior pocket when not in use or allow-
ing the battery to sit in a conditioned room until it is
sufficiently warm.
If the tool temperature is below 0°F (-20°C), only the red
LED will be on and the tool will not operate unless warmed
to above 0°F (-20°C).
Maintenance Instructions
WARNING
Make sure battery is removed from tool before per-
forming maintenance or making any adjustment.
RP 210 Press Tools
Cleaning And Lubrication
1. Wipe the tool clean daily with a clean dry cloth.
2. Inspect the attachment mounting pin and lubricate the
pin with silicone lubricant as needed.
3. Check return springs in attachments with each use.
Attachments should open and close freely with only
moderate finger effort required.
Required Maintenance At RIDGID
Authorized Service Center
After 30,000 cycles, the tool will show a blinking yellow
LED on the display panel as long as the tool is turned on
to indicate that it is time for maintenance and recalibration.
The tool will not run if it is not serviced within 2,000 more
cycles (32,000 total) after the yellow blinking LED begins.
10
All manuals and user guides at all-guides.com
Accessories
The following tool accessories have been de signed
to function with the RP 210 Press Tools. Other
accessories suitable for use with other tools may
become hazardous when used on the RP 210. To
prevent serious injury, use only accessories specif-
ically designed and recommended for use with the
RP 210, such as those listed below.
Ridge Tool Company provides Compact Pressing
attachments designed specifically for use with
RIDGID Compact Press Tools. Only use attach-
ments that are specifically designed to press the fit-
ting system you are installing. For a complete listing
of RIDGID attachments available for this tool, see
the Ridge Tool Catalog on line at www.RIDGID.com
or call Ridge Tool Technical Services (800) 519-
3456.
RP 210-B Press Tool Accessories
Storage
Remove battery from tool and store tool and battery in
case. Avoid storing the tool, batteries or charger in extreme
heat or cold. The tool temperature sensor will not allow the
tool to turn on if oil temperature is not within the temper-
ature range of 0°F (-20°C) to 104°F (40°C). So it may be
neces sary to allow the tool to warm or cool to a temper-
ature within the operating range by placing it in a condi-
tioned room before use. This will be indicated by a red
glowing LED on the display panel.
locked area that is out of reach of children and people
unfamiliar with the RP 210 Press Tool. The tool is dan-
gerous in the hands of untrained users.
Service And Repair
Improper service or repair can make machine
unsafe to operate.
Service and repair on this RP 210 Press Tool must be per-
formed by a RIDGID Authorized Press Tool Service Cent -
er. The tool fasteners have been marked to indicate if
service has been performed by unauthorized individuals.
Ridge Tool Company
WARNING
Catalog
No.
Description
31013
18V 1.1 Ah Lithium-Ion Battery Pack
32743
18V 2.2 Ah Lithium-Ion Battery Pack
27908
18V 3.3 Ah Lithium-Ion Battery Pack
32068
115V Charger
31023
Carrying Case (Plastic)
Store the carrying case in a dry, secured,
WARNING
WARNING
Publicité
