Elica HIDDEN 2.0 @ IX/A/52 Prescriptions De Montage Et Mode D'emploi page 8

Smartphone store by searching for the Elica Connect App.
• Future changes: Elica reserves the right to make any
changes deemed useful to improve the Elica Connect
service. As a result, the descriptions contained in this
manual are not binding and should be treated as purely
indicative.
OPERATION
T3
T2
T1
T1= WiFi key
• WiFi configuration: if the WiFi function is not configured,
press for about 2 seconds to enter WiFi configuration mode
and follow the instructions on the App to complete the
procedure.
During the configuration procedure, the button will light up
indicating the connectivity status (see WiFi status Table).
To interrupt the WiFi configuration procedure, press for
about 2 seconds when the button is lit up and is flashing
fast.
Once the WiFi function has been configured, if you want to
change it, press for about 6 seconds to reset the WiFi
parameters (the button will turn off) and repeat the
configuration procedure.
• WiFi activation/deactivation: after the configuration, it is
possible to deactivate/activate the WiFi function. Press for
about 2 seconds to deactivate/activate the
WiFi function. Deactivating the function does not cause the
loss of the WiFi parameters.
WiFi status table
WiFi button Device connection status
Light off WiFi not configured or off
Light on
WiFi connected
steady white
Light flashing
Attempt to connect to the WiFi rou-
ter
fast orange
Light flashing
Attempt to connect to the Elica
cloud
slow orange
Remote command being received
White light on with
(e.g. engine ignition or light turned
short flashing light
on)
L2 - L3
L1
8
T2= Suction speed control key (power):1, 2, 3, intensive
Note: Intensive speed lasts about 5 minutes, after which
speed 3 is set automatically.
T3= ON/OFF key (short press) and light intensity
adjustment (long press).
Light colour temperature adjustment: With the light ON,
press and hold T1 + T3 to change the light colour
temperature.
Filter saturation indicator
The hood indicates when maintenance is needed for the
following filters:
Grease filter alarm (every 40 hours of use
approximately):
- T1+T2+T3 ON red for 3 seconds when the motor is
switched on.
- T1+T2+T3 ON red for 30 seconds when the motor is
switched off.
After performing maintenance on the filters, it is necessary
to perform the grease filter saturation reset.
Activated carbon odour filter (roughly every 160
operating hours):
- T1 ON and T2+T3 flashing, red for 3 seconds when the
motor is switched on
- T1 ON and T2+T3 flashing, red for 30 seconds when the
motor is switched off.
After performing maintenance on the filters, it is necessary
to perform the activated carbon odour filter saturation reset.
Reset filter saturation
After performing maintenance on the filters, press and hold
keys T1 and T3; LEDs L1, L2 and L3 will flash red briefly
and then turn off.
Activation of activated carbon odour filter saturation
indicator
This indicator is normally deactivated. To activate it,
proceed as follows:
With the hood switched off, press and hold T1 and T2
simultaneously: L1 will light up first, then also L2 and L3,
then, when the keys have been released, LEDs L2 and L3
will flash briefly, indicating activation.
Deactivation of carbon filter saturation LED: repeat
the operation described above; LEDs L1, L2 and L3 will
light up first, at the same time, then only L1, after which,
when the keys are released, LEDs L1, L2 and L3 will light
up again, indicating deactivation.
MAINTENANCE WARNINGS
• Cleaning: For cleaning, simply use a cloth moistened
with neutral liquid detergents. Do not use cleaning tools or
instruments.
For product maintenance, see the images at the
end of the installation marked by this symbol.