Publicité
Les langues disponibles
Les langues disponibles
Install Deflector Kit Bracket
This assembly is required for use when a single or double
built-in oven is installed in a flush installation.
1. Flex the upper vent piece (C) away from the lower vent
piece (D) to slide the deflector bracket (B) between them.
Some force may be required to flex the upper vent trim (C)
away from the lower vent trim (D). Some force may also
be required to flex the deflector bracket (B) and slide it
into position. Make sure screw holes are properly aligned
between the two pieces. See the following illustration.
2. Install the deflector bracket (B) to the lower vent piece (D)
using two #8-18 x
/
" (6.3 mm) screws on each side.
1
4
NOTE: On 27" (68.6 cm) models, only one #8-18 x
mm) screw is used on each side.
A
B
A
A. #8–18 x
/
" (6.4 mm) screws
1
4
B. Deflector bracket
3. Align vent tab (B) with oven frame (A) as shown in the
following illustration.
4. Using one #8-18 x
/
" (9.5 mm) screw (E) on each side of the
3
8
vent tab (B), fasten the vent securely to the oven.
E
D
A. Oven frame
B. Vent tab
C. Oven vent
/
" (6.3
1
4
C
D
C. Upper vent piece
(supplied with oven)
D. Lower vent piece
(supplied with oven)
A
B
C
D. Deflector bracket
E. #8–18 x
/
" (9.5 mm) screw
3
8
5. Replace the oven racks.
6. Replace the oven door. See the "Replace Oven Door(s)"
section.
7. Check that the door is free to open and close. If it is not,
repeat the removal and installation procedures. See the
"Prepare Built-In Oven" section.
8. Repeat for lower oven door.
9. Reconnect power.
10. The display panel will light briefly, and "PF" should appear
in the display.
11. If the display panel does not light, refer to the "Assistance
or Service" section of the Use and Care Guide provided
with your built-in oven or contact the dealer from whom you
purchased your oven.
Complete Installation
B
1. Check that all parts are now installed. If there is an extra
C
part, go back through the steps to see which step was
skipped.
D
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. For oven use and cleaning, read the Use and Care Guide.
Check Operation of Single and Double Ovens
1. Turn on power.
2. At first use, set up the clock and any other preferences
if available. For more information, read the Use and Care
Guide.
3. Press BROIL on single oven models.
NOTE: Press UPPER BROIL or LOWER BROIL on double
oven models.
4. Set the temperature.
5. Press START.
If oven(s) does not operate, check the following:
Household fuse is intact and tight, or circuit breaker has
■
not tripped.
Electrical supply is connected.
■
See "Troubleshooting" section in the Use and Care
■
Guide.
6. When oven has been on for 5 minutes, feel for heat.
If you do not feel heat or if an error message appears in the
display, turn off the oven and contact a qualified technician.
7. Press UPPER CANCEL/LOWER CANCEL on double ovens,
or press CANCEL on single ovens.
If you need Assistance or Service:
Please reference the "Assistance or Service" section of the Use
and Care Guide or contact the dealer from whom you purchased
your built-in oven.
9
Publicité
