DeWalt DWE46253 Guide D'utilisation page 13

Petit outil de finition de surface à angle pour service dur à commutateur à glissière
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

4. Position hands and body away from wheel and
door opening.
5. Place the door edge flush to work surface, turn the tool
on and begin grinding. Remove the tool from work
surface before turning the tool off.
6. When flush grinding is complete, turn off the tool and
disconnect from power source. Allow the tool to stop
rotating before laying it down.
7. Using the edging door tab
into the closed position.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Replace Brush Skirt (Fig. A)
1. Turn off the tool and disconnect from power source.
2. Push worn brush skirt from brush skirt removal
holes 
.
 14 
3. Press new brush skirt into brush skirt removal holes
until secure.
Replacement brush skirts are available at extra cost from
your local dealer or authorized service center. If you need
assistance in locating any accessory, please contact D
Industrial Tool Co., 701 East Joppa Road, Towson, MD
21286, call 1–800–4-D
WALT (1–800–433–9258) or visit our
e
website: www.D
WALT.com.
e
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D
WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
 16 
, rotate door until it snaps
WALT
e
WALT
e
WALT Industrial
e
Repairs

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D
WALT factory service center
e
or a D
WALT authorized service center. Always use
e
identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D
WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from
the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail
of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
433-9258). This warranty does not apply to accessories
or damage caused where repairs have been made
or attempted by others. THIS LIMITED WARRANTY IS
GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.In
addition to the warranty, D
WALT tools are covered by our:
e
1 YEAR FREE sERViCE
D
WALT will maintain the tool and replace worn parts
e
caused by normal use, for free, any time during the first year
after purchase.
90 DAY MOnEY BACK gUARAnTEE
If you are not completely satisfied with the performance of
your D
WALT Power Tool, Laser, or Nailer for any reason, you
e
can return it within 90 days from the date of purchase with
a receipt for a full refund – no questions asked.
English
WALT (1-800-
e
11

Publicité

Table des Matières
loading

Table des Matières