Publicité
Les langues disponibles
Les langues disponibles
EN
You can override the function at any
time by turning off the plate, by chan-
ging the power level or by choosing a
different special function.
MELTING FUNCTION
This function maintains a low tempera-
ture in the cooking zone. Ideal for de-
frosting food or for slowly melting other
food types as chocolate, butter, etc.
To activate it, select the plate, and
press on the iCooking sensor
until the LED (18) located on the icon
lights up. Once the function is
activated, the symbol
will appear
on the power indicator (3).
You can override the function at any
time by turning off the plate, by chan-
ging the power level or by choosing a
different special function.
SIMMERING FUNCTION
This feature allows you to keep
simmered.
After the food is boiled, enable the
plate by selecting it, and press the
iCooking sensor
(16) until the LED
(19) located on the icon
up. Once the function is activated, the
symbol
will appear on the power
indicator (3).
You can override the function at any
time by turning off the plate, by chan-
ging the power level or by choosing a
different special function.
Safety shut off
If due to an error one or several
heating zones do not switch off, the
appliance will be automatically discon-
nected after a set amount of time (see
table 1).
26
All manuals and user guides at all-guides.com
Table 1
Selected
power level
1
2
3
4
5
(16)
6
7
8
9
P
When the "safety switch off" function
has been triggered, a 0 is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
Keep in mind that this safety function
turns on even when the touch control
is off!
Take precaution and do not place
objects on the touch control!
lights
Timer function
(countdown clock)
This function facilitates cooking given
that you don't have to be present: You
can set a timer for a plate, and it will
turn off once the desired time is up.
For these models, you can simultane-
ously program each plate for durations
ranging from 1 to 90 minutes.
Setting a timer on a plate
To set a timer on a plate, you should
take the following steps.
1 Select the desired plate by directly
touching its corresponding indicator
(3) and choose a power level with
the cursor slider (2).
2 The two digits of the timer for the
plate selected will turn on, showing
"- - ". You can set the amount of
time desired with sensors
and
(11).
3 After a few seconds, the countdown
TEMPO MÁXIMO DE MA-
XIMUM OPERATING TIME
(in hours)
Once the countdown has finished, the
timed plate will turn off and a series of
0
beeps will be heard. They can be stop-
ped by touching either of the sensors
8
8
the clock.
5
Disconnecting the clock
4
4
If you wish to stop the clock before the
3
programmed time is up, this can be
done at any time by simply adjusting
2
its value to '--'.
2
1 Select the plate you wish to stop
1
10 minutes, readjusts to 9
2 Adjust the value of the clock to "--"
By using this function it is possible to
achieve that two plates, as shown in
the screen, function at the same time,
both for selecting a power level as well
as for activating the timer function.
To activate this function you should
press the sensor
Upon doing so, the decimal points (14)
of the plates light up and both turn to
power level 5.
The timer (12) of the lower plate will
turn off, and from then on it will be the
upper one that indicates the values of
the clock for both.
To deactivate this function you should
press the sensor again
(15). cal service can handle or repair
the appliance, including replacement
of the power cable.
(10)
* Use pots or pans with thick, comple-
begins. When there is less than one
minute left, the clock will begin to
count down in seconds.
(10) or
(11) associated with
the timer on by directly touching its
corresponding indicator (3).
by using the "less" sensor
This can also be done more quickly
by pushing the "less" and "more"
sensors
(10) and
(11) at the
same time.
Flex Zone and Synchro
(depending on model)
(14) or
(14) or
Suggestions and
recommendations
tely flat bottoms.
(10).
(15).
Publicité
