Télécharger Imprimer la page

Teka P21378R00 Instructions Pour L'installation Et L'entretien page 25

Plaques de cuisson vitrocéramique touch control

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 37
All manuals and user guides at all-guides.com
If the on/off sensor
(1) is used to
turn off the appliance while the block
function is activated, it won't be possi-
ble to turn the cooktop on again until
it unblocks.
Stop&Go Function
This function puts the cooking process
on pause. The timer will also be pau-
sed if it is activated.
Activating the Stop&Go function
Touch the Stop&Go sensor
for one second. The pilot (9) lights
up and the
power indicators will show the symbol
to indicate cooking has been
paused.
Deactivating the Stop&Go function
Tap again on Stop&Go
slider cursor sensors (2); the indicator
light will go off (9) and cooking will be
resumed in same conditions of power
and timer levels that were set before
the pause.
Power Function
This function supplies "extra" power
to the plate, above the nominal value.
Said power depends on the size of the
plate, (see values specified with * in
the presentation section), with the pos
sibility of reaching the maximum value
permitted by the generator.
1 Select the desired plate with the
corresponding sensor (3). The deci
mal point will light up.
2 On the cursor Slider, push directly
on position (5). The power level
indicator will show the symbol P,
and the plate will start to supply
extra power.
The Power function has a maximum
duration as specified in table 1. After
this time, the power level will automati-
cally adjust to 9.
Function IQuickboiling
This innovative function is of an enor-
mous help if you want to cook pasta,
rice, eggs, or boil any kind of food. This
function allows you to perform this co-
oking method "almost" automatically.
This function is available only in the
plates where this symbol appears
Pot requirements
For properly using boil control, the pot
must have the following characteris
tics:
Bottom size as close as possible to the
diameter of the plate.
(8)
- NO COVER.
- Filled more than halfway of its capa-
city with room temperature water
(never use lukewarm or hot water).
Not fulfilling these requirements
will result in inadequate control of
boiling.
WARNING: do not use this
(8) and
function for cooking methods other
than boiling water. Never use oil. It
can overheat and create flames.
Activating the function:
Select the proper plate. The decimal
point lights up.
Push sensor
on the plate indicator and the pilot (20)
will turn on. In the timer for this plate,
a moving segment will appear which
indicates that the system has started
to monitor cooking.
When the system detects that it is
about to boil, an initial beep will go off.
Take this time to prepare the food you
want to boil or cook.
After 30 seconds, a second beep will
go off. If you haven't done it already,
now is time to put the food into the pot.
After the second beep, the system will
activate the timer as a chronometer so
that you can control how long the food
has been boiling.
A few seconds after the chronometer is
activated, a third beep will go off indi-
cating that, from this moment on, the
system will reduce the energy supplied
in order to maintain a gentle and ste-
ady boil. The chronometer will remain
active until cooking has finished.
If desired, the chronometer can be
deactivated and you can set a time for
the countdown to occur and the plate
to automatically turn off (see section
Timer Function).
Deactivating the function
You can cancel the function at any time
.
by simply turning off the plate or modif
ying the power level.
The Touch Control has special featu-
res that help the user to cook through
the iCooking sensor
functions are available depending on
the model.
To activate a special feature on a zone:
1 First it should be selected; and then,
2 Now click on the iCooking sensor
(22). An
will appear
If you want to cancel a special active
function at any time, you should touch
the "slider" cursor sensor (2) of the
related zone to select it. The decimal
point (4) of the power indicator (3) will
light up. Then, touch again the "slider"
(2) cursor to set a new power level or
to power off the zone, or you can choo-
se a different special function touching
again on the iCooking sensor
KEEP WARM FUNCTION
This function automatically sets an
appropriate power level to keep the
cooked food hot.
To activate it, select the plate, and
press on the iCooking sensor
until the LED (17) located on the icon
activated, the symbol
on the power indicator (3).
Special functions:
iCooking
(16). These
the decimal point (4) will be active
on the power indicator (3).
(16). The sequentially succes-
sive presses will go over all the
Cooking functions available in each
zone one by one. These functions
will show the activation with the
corresponding leds (17), (18), and
(19).
lights up. Once the function is
will appear
EN
(16).
(16)
25

Publicité

loading