Replacing The Blades; Software Update; Ordering Spare Parts; Storage - EINHELL FREELEXO Basic Instructions D'origine

and turning brown. It is important therefore to
change the blades regularly in order to obtain
a clean and straight cut.
•
Check the bottom of the robot lawn mower
for dirt at regular intervals. Clean your robot
lawn mower regularly. Remove heavy soiling
immediately.
•
Heavy soiling of the robot lawn mower is
possible in the first weeks of using it for the
first time after a conventional law mower had
previously been used. In these first few weeks
you should check the bottom of your robot
lawn mower more often.
•
Shorten the lawn only in small steps in order
to prevent heavy soiling.
•
There are no other parts inside the equipment
which require maintenance.

7.2.1 Replacing the blades

Only replace the blades with genuine blades, as
this will ensure top performance and safety.
The robot lawn mower is equipped with three bla-
des (10) fi tted to a blade plate (11). These blades
(10) have a service life of up to 3 months (if they
do not strike any obstacles). Please replace all
three blades (10) at the same time to ensure that
there is no possibility of any impairment to the
effi ciency and balance of your equipment.
To change the blades (10), proceed as follows
(Fig. 12) - Caution! - Wear work gloves:
1. Use a screwdriver to block the rotation of
the blade plate (11). Do this by inserting the
screwdriver through the holes in the blade
plate (11) and the protective ridge.
2. Undo the fastening screws
3. Remove the blades (10) and replace them
with new ones. Always replace all three bla-
des (10) as a set.
4. Then retighten the fastening screw. Check
that the new blades (10) are able to rotate
freely.
Perform a general inspection of the robot lawn
mower at regular intervals and remove any depo-
sits which may have accumulated. At the start of
each season, ensure that you check the condition
of the blades (10). If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.

7.2.2 Software update

If you want to update the software, copy the new
software to an empty USB stick (format the USB
stick fi rst if necessary). Make sure that the rechar-
geable battery is fully charged before you carry
Anl_FREELEXO_Basic_SPK9.indb 41 Anl_FREELEXO_Basic_SPK9.indb 41
GB
out the following steps.
1. Place the robot lawn mower in the area to be
mowed. The robot lawn mower must not be
in the charging station during the software
update.
2. Connect a USB stick to the USB connection
as shown in the illustration. (Fig. 11).
3. Switch on the main switch (7) (ON).
4. The update operation will start automatically
and the time LEDs (50) will fl ash.
5. When all 4 time LEDs (50) light up together
and the mower beeps continuously, the pro-
cess has been completed.
6. Pull out the USB stick and close the cover.
7.2.3 Repairing the perimeter wire
If the perimeter wire (18) gets severed at any
point, use the supplied cable connectors (16) to
repair it. To do so, insert both ends of the severed
perimeter wire (18) into the cable connector (16)
and squeeze it together with the help of a pair of
pliers. Connect the power plug to the socket out-
let. Then check whether it is working properly by
checking the LED indicator (21) on the charging
station (19).

7.3 Ordering spare parts

Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Replacement blades Art. No.: 34.140.20

8. Storage

Fully charge up the rechargeable battery (22) be-
fore putting it into storage over winter and switch
off the robot lawn mower at the main switch (7)
(OFF). Take the rechargeable battery (22) out
of the equipment. Disconnect the power supply
unit (13) from the power supply and the charging
station (19).
The perimeter wire (18) can be left outdoors over
winter. However, make sure that the connections
are protected against corrosion. To do so, discon-
nect the connections of the perimeter wire (18)
from the charging station (19).
- 41 -
16.12.2020 13:33:36 16.12.2020 13:33:36