Changing The Battery; Replacing The Blades; Ordering Spare Parts - EINHELL GC-RM 500 Instructions D'origine

Masquer les pouces Voir aussi pour GC-RM 500:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 47
4. Press the "4" button / lock button (65) to start
the update. The time LEDs (50) show the cur-
rent progress. When all 5 time LEDs (50) are
lit together, this means that the process has
been completed and the robot lawn mower
will switch to its normal operating state.
5. Pull out the USB stick and close the battery
cover (9) again.
7.3 Maintenance
Worn or damaged blades (10) and their fas-
tening screws must always be replaced as a
set.
Replace excessively worn or damaged parts
immediately.
In order to ensure that you enjoy the equip-
ment for many years to come, all screwed
parts, as well as the wheels and axles, should
be cleaned and lubricated.
Keeping your robot lawn mower in good
condition not only ensures a long lifespan
and high performance, but also enables the
equipment to thoroughly cut your grass with
minimal effort.
The blades (10) are subject to more wear and
tear than any other component. Therefore,
routinely check the condition of the blades
(10) and make sure that they are tightly fas-
tened. An excessively vibrating robot lawn
mower can indicate that the blades (10) are
damaged or have become deformed from
striking an object. If the blades (10) are worn
or damaged, they must be replaced immedia-
tely.
There are no other parts inside the equipment
which require maintenance.

7.4 Replacing the blades

Only replace the blades with genuine blades, as
this will ensure top performance and safety.
The robot lawn mower is equipped with three bla-
des (10) fi tted to a blade plate (11). These blades
(10) have a service life of up to 3 months (if they
do not strike any obstacles). Please replace all
three blades (10) at the same time to ensure that
there is no possibility of any impairment to the
effi ciency and balance of your equipment.
To change the blades (10), proceed as follows
(Fig. 12):
1. Undo the fastening screws
2. Remove the blades (10) and replace them
with new ones. Always replace all three bla-
des (10) as a set.
3. Then retighten the fastening screw. Check
Anl_GC_RM_500_SPK9.indb 38
Anl_GC_RM_500_SPK9.indb 38
GB
that the new blades (10) are able to rotate
freely.
Perform a general inspection of the robot lawn
mower at regular intervals and remove any depo-
sits which may have accumulated. At the start of
each season, ensure that you check the condition
of the blades (10). If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.

7.5 Changing the battery

Only replace the rechargeable battery with a ge-
nuine rechargeable battery, as this will ensure top
performance and safety.
To change the rechargeable battery (22), proceed
as follows (Fig. 10):
1. Undo the six fastening screws in the battery
cover (9).
2. Take the rechargeable battery (22) out of the
robot lawn mower.
3. Then insert the new rechargeable battery (22)
and fasten the battery cover (9) with the faste-
ning screws.
7.6 Repairing the perimeter wire
If the perimeter wire (18) gets severed at any
point, use the supplied cable connectors (16) to
repair it. To do so, insert both ends of the severed
perimeter wire (18) into the cable connector (16)
and squeeze it together with the help of a pair of
pliers. Connect the power plug to the socket out-
let. Then check whether it is working properly by
checking the LED indicator (21) on the charging
station (19).

7.7 Ordering spare parts

Please provide the following information when
ordering spare parts:
Type of unit
Article number of the unit
ID number of the unit
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Replacement blades Art. No.: 34.140.20
- 38 -
14.11.2019 10:53:22
14.11.2019 10:53:22

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

34.139.30

Table des Matières