Milwaukee M18 FUEL 2984-20 Manuel De L'utilisateur page 6

Care of Accessories
Points, cones, plugs, grinding wheels and cut-off
wheels should be protected from:
• wetness and extreme humidity
• any type of solvent
• extreme changes in temperature
• dropping and bumping
Points, cones, plugs, grinding wheels and cut-off
wheels should be stored:
• in an organized way so points, cones, plugs or
wheels can be removed without disturbing or dam-
aging other points, cones, plugs or wheels
• with their safety information
Points, cones, plugs, grinding wheels and cut-off
wheels should NOT be dropped, rolled or bumped.
Discard points, cones, plugs, or wheels that have
been dropped, rolled, bumped, subjected to extreme
changes in temperature, or come into contact with
solvents or wetness.
Installing/Removing/Cleaning
the Dust Screen
Using the dust screen will increase the performance
and extend the life of the tool.
1. To attach the dust screen, snap the screen over
the tool's handle.
2. To remove the dust screen, insert a flat screw-
driver into the notch at the top of the dust screen
and pry away from the tool.
3. To clean the dust screen, tap against a hard sur-
face, or blow clean with compressed air.
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
To reduce the risk of injury, always
WARNING
remove battery pack before attach-
ing or removing accessories or making adjust-
ments. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
Always wear proper eye protection marked to
comply with ANSI Z87.1.
If the grinder begins vibrating, immediately stop
the motor and check to see if the accessory
is dull. Dull accessories will cause the tool to
vibrate and could force the collet to fly off the
tool. Always replace or sharpen dull accessories.
Accessories are designed for specific uses. Only
use points, cones, plugs, grinding wheels and
cut-off wheels for applications for which they
were designed. Follow manufacturer's care and
use instructions.
MILWAUKEE Variable Speed Grinders have a
speed dial located on the end of the handle to set
the maximum speed. Rotate the speed dial to "5"
for maximum speed, "1" for minimum speed.
General Operation
1. If you have just installed an accessory or are
beginning a period of work, test it by letting it spin
for one minute before applying it to the workpiece.
WARNING! Never use an accessory that has been
dropped. Out-of-balance or damaged accessories
can mar workpiece, damage the tool, and cause
stress that may cause accessory failure.
2. Use a clamp, vise or other practical means to hold
your work, freeing both hands to control the tool.
3. WARNING! Hold tool securely with both hands.
Start the tool.
4. To start the tool, grasp the front and rear grips
firmly and slide the switch to ON.
5. Allow accessory to come to full speed before
beginning work.
6. Control pressure and surface contact between ac-
cessory and workpiece. WARNING! Never bang
accessories onto work.Too much pressure causes
accessory failure or slows speed.
7. To stop the tool, release the switch. Make sure the tool
comes to a complete stop before laying the tool down.
8. To lock-on the switch, slide the switch to ON and
press down on the front of the switch. To stop the
tool, press and release the switch. Make sure the
tool comes to a complete stop before laying down
the tool.
Electric Brake
The electric brake engages when the switch is re-
leased, causing the wheel to stop within seconds.
There may be a delay between the time the switch is
released and when the brake engages. Occasionally
the brake may miss completely. If the brake misses
frequently, have the tool serviced by an authorized
MILWAUKEE service facility. Make sure the tool
comes to a complete stop before laying it down.
Paddle Switch Operation
To start the tool, grasp the handle and side handle
firmly. Push the lock-off button forward and squeeze
the paddle switch.
To stop the tool, release the paddle switch. Make
sure the tool comes to a complete stop before laying
down the tool.
6
Speed Dial