Bosch GWX 18V-7 Notice Originale page 24

24 | English
Restart protection
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
To restart the tool, set the on/off switch (4) to the off posi-
tion and then switch the power tool on again.
Soft start
The electronic soft start limits the torque when the power
tool is switched on and increases the service life of the mo-
tor.
Working Advice
Exercise caution when cutting slots in structural walls;
u
see the "Information on structural design" section.
Clamp the workpiece if it is not secure under its own
u
weight.
Do not load the power tool so heavily that it comes to a
u
stop.
If the power tool has been subjected to a heavy load,
u
continue to run it at no-load for several minutes to
cool down the accessory.
Do not use the power tool with a cut-off stand.
u
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
If the power tool becomes electrostatically charged, the
built-in electronics will switch the power tool off. Press the
on/off switch (4) again to restart the power tool.
Rough grinding
Never use cutting discs for rough grinding.
u
The best rough grinding results are achieved with a set angle
of 30° to 40°. Move the power tool back and forth with mod-
erate pressure. This will ensure that the workpiece does not
become too hot or discolour and that grooves are not
formed.
Flap Disc
With the flap disc (accessory), curved surfaces and profiles
can be worked. Flap discs have a considerably higher ser-
vice life, lower noise levels and lower sanding temperatures
than conventional sanding sheets.
Cutting Metal
Always use the protective guard for cutting (10) when
u
cutting bonded abrasives.
When carrying out abrasive cutting, use a moderate feed
that is suited to the material being machined. Do not exert
pressure on the cutting disc and do not tilt or swing the
power tool.
Do not attempt to reduce the speed of a cutting disc coming
to a stop by applying pressure from the side.
1 609 92A 6KH | (15.07.2021)
Cutting Stone (see figure A)
Provide sufficient dust extraction when cutting stone.
u
Wear a dust mask.
u
The power tool may be used only for dry cutting/grind-
u
ing.
For best results when cutting stone, use a diamond cutting
disc.
When using the extraction guard for cutting with a cutting
guide (20), the vacuum cleaner must be approved for vacu-
uming stone dust. Suitable vacuum cleaners are available
from Bosch.
crete with a high pebble content, the diamond cutting disc
can overheat and become damaged as a result. This is
clearly indicated by circular sparking, rotating with the dia-
mond cutting disc.
If this happens, stop cutting and allow the diamond cutting
disc to cool down by running the power tool for a short time
at maximum speed with no load.
If work is noticeably slower and with circular sparking, this
indicates that the diamond cutting disc that has become
dull. You can resharpen the disc by briefly cutting into abras-
ive material (e.g. lime-sand brick).
Information on structural design
Slots in load-bearing walls are subject to DIN 1053 part 1 or
country-specific regulations. These regulations must be ob-
served under all circumstances. Seek advice from the re-
sponsible structural engineer, architect or construction su-
pervisor before starting work.
Recommendations for optimal handling of the battery
Protect the battery against moisture and water.
Only store the battery only within a temperature range of -20
to 50 °C. Do not leave the battery in your car in the summer,
for example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
The power tool must always
work in an up-grinding mo-
tion. Otherwise, there is a
risk that it will be pushed
uncontrolled out of the cut.
For best results when cut-
ting profiles and rectangular
tubing, start at the smallest
cross section.
Switch on the power tool
and position it with the
front part of the cutting
guide on the workpiece.
Move the power tool with a
moderate feed motion that
is suited to the material be-
ing machined.
When cutting especially
hard materials such as con-
Bosch Power Tools