Technical Data
Impact drill
Article number
Rated power input
Power output
No-load speed
Impact rate
Rated torque
Speed preselection
Clockwise/anticlockwise
rotation
Spindle collar diameter
Max. drilling diameter
– Concrete
– Steel
– Wood
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Values can vary depending upon the product and are subject to application and environmental conditions. For further information
www.bosch-professional.com/wac.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Auxiliary Handle (see figure A)
Do not operate your power tool without the auxiliary
u
handle (9).
You can swivel the auxiliary handle (9) to any angle for a safe
work posture that minimises fatigue.
Turn the lower gripping end of the auxiliary handle (9) anti-
clockwise and set the depth stop (10).
Pull the depth stop (10) far enough out that the distance
between the drill bit tip and the edge of the depth stop (10)
corresponds to the required drilling depth X.
Then, turn the lower gripping end of the auxiliary handle (9)
clockwise to retighten it.
The fluting on the depth stop (10) must face upwards.
Changing the Tool
Keyless Chuck (see figure B)
Hold the rear sleeve (3) of the keyless chuck (1) firmly and
turn the front sleeve (2) in the rotational direction ➊ until
the tool can be inserted. Insert the tool.
Hold the rear sleeve (3) of the keyless chuck (1) and firmly
tighten the front sleeve (2) by hand in the rotational direc-
Bosch Power Tools
GSB 13 RE
3 601 B27 1..
W
650
W
353
–1
min
3150
–1
min
47000
Nm
1.8
–
●
mm
43
mm
13
mm
10
mm
20
mm
1.5–13
kg
1.6
/ II
tion ➋ until it stops clicking. This will automatically lock the
drill chuck.
The lock will disengage again if you turn the front sleeve (2)
in the opposite direction to remove the tool.
Keyed chuck (see figure C)
Open the keyed chuck (13) by turning it until the tool can be
inserted. Insert the tool.
Insert the drill chuck key (12) into the corresponding holes
of the keyed chuck (13) and clamp the tool evenly.
u
Screwdriving Tools (see figure D)
You should always use a universal bit holder (14) when using
screwdriver bits (15). Only use screwdriver bits that fit the
screw head.
For screwdriving, make sure the "drilling/impact drilling" se-
lector switch (4) is always set to the "drilling" symbol.
Changing the Drill Chuck
u
Removing the Drill Chuck (see figure E)
To remove the keyless chuck (1), clamp a hex key (16) in
the keyless chuck (1) and position an open-ended spanner
GSB 1300 RE
GSB 16 RE
3 601 B27 1..
3 601 B28 1..
650
750
353
456
3150
3250
47000
48500
1.8
–
●
43
13
10
20
1.5–13
1.5–13
1.6
/ II
Wear protective gloves when changing tools. The drill
chuck may heat up significantly when it is used for long
periods.
Pull the plug out of the socket before carrying out any
work on the power tool.
1 609 92A 952 | (18.09.2023)
English | 7
GSB 1600 RE
3 601 B28 1..
750
456
3250
48500
2.1
2.1
●
●
●
●
43
43
16
16
12
12
25
25
1.5–13
1.8
1.8
/ II
/ II