Publicité
Les langues disponibles
Les langues disponibles
All manuals and user guides at all-guides.com
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1
Press the TOOLS button.
Press the ▲ or ▼ button to select Receiver, then press the ENTER
button.
2
Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
3
Press the EXIT button to exit.
When the receiver (home theater) is set to On, you can hear sound
output from the TV's Optical jack. When the TV is displaying a DTV(air)
signal, the TV will send out 5.1 channel sound to the Home theater
receiver. When the source is a digital component such as a DVD and is
connected to the TV via HDMI, only 2
channel sound will be heard from the Home Theater receiver.
If your receiver supports audio only, it may not appear in the device list.
The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical
Out jack of the TV.
If there is a power interruption to the TV when the Receiver is On (by disconnecting the power cord or a
power failure), the TV Speaker may be set to Off when you turn the TV on again.
Check Points before Requesting Service
Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet + device... appears on the
screen.
The Anynet + device does not play.
The connected device is not
displayed.
The TV programme cannot be
recorded.
The TV sound is not output
through the receiver.
Solution
■ Check if the device is an Anynet + device. The Anynet + system supports
Anynet + devices only.
■ Connect only one receiver.
■ Check if the Anynet + device power cord is properly connected.
■ Check the Anynet + device's Video/Audio/HDMI cable connections.
■ Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet + exclusive remote control.
■ Anynet + doesn't work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI cable, please make sure to search
devices again or restart your TV.
■ Check if the Anynet + Function of Anynet + device is set on.
■ Check if the Anynet + device is properly connected to the TV and check if the
Anynet + (HDMI-CEC) is set to On in the Anynet + Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then press the
TOOLS button to show the Anynet + menu and select a menu you want.
■ Select View TV in Anynet + menu.
■ Press the SOURCE button on the TV remote control and select a device
other than Anynet + devices.
■ Press any of CH, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a tuner-
embedded Anynet + device is not connected.)
■ You cannot use the remote control when you are configuring Anynet + or
switching to a view mode.
■ Use the remote control when the Anynet + setting or switching to view mode is
complete.
■ You cannot use the play function when Plug & Play is in progress.
■ Check whether or not the device supports Anynet + functions.
■ Check whether or not the HDMI cable is properly connected.
■ Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
■ Search Anynet + devices again.
■ You can connect an Anynet + device using the HDMI cable only. Some HDMI
cables may not support Anynet + functions.
■ Check whether the antenna jack on the recording device is properly
connected.
■ Connect the optical cable between TV and the receiver.
English - 47
Tools
View TV
Device List
Recording : DVD
DVD Menu
DVD Menu
Picture Mode
:
Dynamic
Sound Mode
:
Standard
Sleep Timer
:
Off
▼
Move
Enter
Exit
Publicité
